Address;Name;Size "$00000";"Hexdump";"" "$10000";"Eeprom-Kennung";"50x1" "$10DDC";"Codeword ABS sensor selection for MS-Sport";"1x1" "$10DDC";"Codeword ABS sensor selection for MS-Sport";"1x1" "$10D82";"Acceleration X-axis auto-zero offset action";"1x1" "$13FBC";"Acceleration X-axis default value in case of error";"1x1" "$1004D";"Acceleration X-axis error mode";"1x1" "$10D83";"Acceleration X-axis filtering time constant";"1x1" "$13FBE";"Acceleration sensor X-axis gradient";"1x1" "$13FC0";"Acceleration sensor X-axis maximum diagnostic voltage";"1x1" "$13FC2";"Acceleration sensor X-axis minimum diagnostic voltage";"1x1" "$10D84";"Acceleration Y-axis auto-zero offset action";"1x1" "$13FC4";"Acceleration Y-axis default value in case of error";"1x1" "$1004E";"Acceleration Y-axis error mode";"1x1" "$10D85";"Acceleration Y-axis filtering time constant";"1x1" "$13FC6";"Acceleration sensor Y-axis gradient";"1x1" "$13FC8";"Acceleration sensor Y-axis maximum diagnostic voltage";"1x1" "$13FCA";"Acceleration sensor Y-axis minimum diagnostic voltage";"1x1" "$10D86";"Acceleration Z-axis auto-zero offset action";"1x1" "$13FCC";"Acceleration Z-axis default value in case of error";"1x1" "$1004F";"Acceleration Z-axis error mode";"1x1" "$10D87";"Acceleration Z-axis filtering time constant";"1x1" "$13FCE";"Acceleration sensor Z-axis gradient";"1x1" "$13FD0";"Acceleration sensor Z-axis maximum diagnostic voltage";"1x1" "$13FD2";"Acceleration sensor Z-axis minimum diagnostic voltage";"1x1" "$10D3C";"manual input for adjust of chassis data logging";"1x1" "$10DD4";"After-run maximum allowed duration";"1x1" "$10D93";"Time delay pedal sensor voltage error";"1x1" "$17100";"voltage at lower stop pedal sensor";"1x1" "$10D94";"Time delay ETB common mode error";"1x1" "$17102";"APS Common mode maximum voltage difference";"1x1" "$17104";"voltage at upper stop pedal sensor";"1x1" "$17106";"minimal pedal sensor voltage";"1x1" "$17108";"maximal pedal sensor voltage";"1x1" "$13FD4";"Throttle angle idle-state calibration";"1x1" "$10D88";"Throttle angle idle-state detection threshold";"1x1" "$10D88";"Throttle angle idle-state detection threshold";"1x1" "$13FD6";"Throttle lower set-point angle";"1x1" "$13FD8";"Throttle upper set-point angle";"1x1" "$10D89";"adjustment mode of throttle angle calibration";"1x1" "$13FDA";"Throttle angle default value";"1x1" "$10050";"Throttle error mode";"1x1" "$13FDC";"Throttle angle minimum diagnosis voltage";"1x1" "$13FDE";"Throttle angle maximum diagnosis voltage";"1x1" "$170AE";"Minimum battery voltage threshold for MILSPEC drive";"5x1" "$1234A";"Boost pressure controller battery voltage correction";"5x1" "$1234A";"Boost pressure controller battery voltage correction";"5x1" "$10CCF";"Ladedruck-Regler codeword PI control direction";"1x1" "$12364";"Boost pressure controller integration component factor";"7x1" "$12372";"Boost pressure controller integration component limitation";"1x1" "$12374";"Boost pressure controller integration component limitation";"1x1" "$12396";"Boost pressure pre-control";"15x1" "$17690";"Camshaft phase correction bank 1";"1x1" "$17692";"Camshaft phase correction bank 2";"1x1" "$10DEB";"Time delay control deviation error of cam shaft position PID-controller cam shaft 1";"1x1" "$10051";"VVT error mode maximum control deviation exceeded on cam shaft 1";"1x1" "$17694";"Maximum control deviation cam shaft 1";"1x1" "$10DEC";"Time delay control deviation error of cam shaft position PID-controller cam shaft 2";"1x1" "$10052";"VVT error mode maximum control deviation exceeded on cam shaft 2";"1x1" "$17696";"Maximum control deviation cam shaft 2";"1x1" "$10DED";"codeword negation of the relative cam shaft position 1";"1x1" "$10DEE";"codeword negation of the relative cam shaft position 2";"1x1" "$17698";"Slew rate limit for cam shaft position set point 1";"1x1" "$1769A";"Slew rate limit for cam shaft position set point 2";"1x1" "$1769C";"Hysteresis cam shaft 1 position switching";"1x1" "$1769E";"Hysteresis cam shaft 2 position switching";"1x1" "$176C4";"Camshaft desired position bank 2";"12x10" "$177D8";"CAMPOSSP_2";"12x10" "$178C8";"Threshold cam shaft 1 position switching";"1x1" "$178CA";"Threshold cam shaft 2 position switching";"1x1" "$100A2";"codeword detection camshaft signal bank 1";"1x1" "$100A2";"codeword detection camshaft signal bank 1";"1x1" "$10053";"Camshaft 1 error mode";"1x1" "$100A3";"codeword detection camshaft signal bank 2";"1x1" "$100A3";"codeword detection camshaft signal bank 2";"1x1" "$10054";"Camshaft 2 error mode";"1x1" "$10047";"CAN 2 baudrate (0 = 500kBaud / 1 = 1000KBaud)";"1x1" "$10D3D";"manual input for check mode";"1x1" "$100A4";"Clear all synchronisation counters";"1x1" "$10D3E";"Real time entry for memory, day";"1x1" "$10D3F";"Real time entry for memory, hour";"1x1" "$10D40";"Real time entry for memory, minute";"1x1" "$10D41";"Real time entry for memory, month";"1x1" "$10D42";"Real time entry for memory, second";"1x1" "$13F8E";"Real time entry for memory, year";"1x1" "$10D18";"Codeword clear fuel calculation";"1x1" "$10D19";"Codeword clear total fuel calculation";"1x1" "$10D3A";"Clear lifetime values: ltrevthres | ltrevmax | ltdistkm | lteng";"1x1" "$100A0";"Selection teethcount of crankshaft wheel";"1x1" "$1009A";"Codeword configuration of ignition output during blipper request from Megaline GCU";"1x1" "$10CFF";"Bank correspondence of the individual cylinder (0=bank 1, 1=bank 2)";"8x1" "$10CFF";"Bank correspondence of the individual cylinder (0=bank 1, 1=bank 2)";"8x1" "$10CFF";"Bank correspondence of the individual cylinder (0=bank 1, 1=bank 2)";"8x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$100A1";"Cylinder number";"1x1" "$10D43";"String for data version (30 bytes)";"30x1" "$10D61";"String for data version 2 (30 bytes)";"30x1" "$10D8A";"test byte for DDU2 lamps";"1x1" "$10D8B";"Codeword for enabling of DDU";"1x1" "$1004A";"Diagnosis battery minimum enable threshold";"1x1" "$1004B";"Diagnosis power-on enable delay";"1x1" "$12FE2";"Threshold for diaphragm protection at engine shutdown";"1x1" "$12FE4";"Threshold for diaphragm protection at low-speed";"1x1" "$10D9A";"Drive axle gear ratio";"1x1" "$10D9A";"Drive axle gear ratio";"1x1" "$10D9B";"Selection of drive axle for gear detection over wheel speed";"1x1" "$10D9B";"Selection of drive axle for gear detection over wheel speed";"1x1" "$10055";"EEPROM error mode";"1x1" "$11D14";"ETC nominal throttle position, state blipper gear disengage";"11x1" "$11D47";"ETC nominal throttle position, state blipper active";"5x11" "$11DCE";"ETC nominal throttle position curve, state blipper active";"11x1" "$1710A";"d-constant for ETB control";"1x1" "$1711E";"integrator constant for ETB";"8x1" "$1712E";"maximum ETB control i-part";"1x1" "$17130";"minimum ETB control i-part";"1x1" "$17132";"ETB calibration: duty cycle lower mechanical stop, phase 1";"1x1" "$17134";"ETB calibration: duty cycle to go to limp home position , phase 1";"1x1" "$17136";"ETB calibration: duty cycle upper mechanical stop, phase 1";"1x1" "$17138";"ETB deviation threshold for D-portion activation";"1x1" "$10D95";"Time delay system deviation error";"1x1" "$1713A";"maximal system deviation (supervisor)";"1x1" "$17148";"p constant for ETB control in direction blade closing";"11x1" "$10D96";"Time delay ETB voltage error";"1x1" "$17184";"ETB calibration: duty cycle lower mechanical stop, phase 2";"6x11" "$17208";"Calibration time delay lower mechanical stop phase 1";"1x1" "$1720A";"Calibration time delay lower mechanical stop phase 2";"1x1" "$1720C";"maximal voltage at lower position";"1x1" "$1720E";"Calibration time delay limp home position phase 1";"1x1" "$17210";"Calibration time delay limp home position phase 2";"1x1" "$10D97";"Time delay ETB common mode error";"1x1" "$17212";"ETB Common mode maximum voltage difference";"1x1" "$1723E";"Set point map for ETB";"8x11" "$172F5";"battery voltage correction for ETB";"6x1" "$17328";"ETB calibration: duty cycle upper mechanical stop, phase 2";"6x11" "$173AC";"Calibration time delay upper mechanical stop phase 1";"1x1" "$173AE";"Calibration time delay upper mechanical stop phase 2";"1x1" "$173B0";"minimal voltage at upper position";"1x1" "$173BE";"p constant for ETB control in direction blade opening";"11x1" "$173D4";"minimal voltage of ETB";"1x1" "$173D6";"maximal voltage of ETB";"1x1" "$10044";"hysteresis temperature for fan control";"1x1" "$10045";"temperature threshold for activating fan";"1x1" "$10056";"cooler fan error mode";"1x1" "$13DE6";"Conversion factor mass -> volume";"1x1" "$13DE8";"For internal use only";"1x1" "$10D98";"Fuel pump codeword activation duration";"1x1" "$13FEA";"Fuel pump KL15-on activation duration";"1x1" "$10D99";"Fuel pump manual activation (0=deactivated, 1=activated)";"1x1" "$10057";"Fuel pump error mode";"1x1" "$13DEA";"Delay time to disable refuel switch function after launch";"1x1" "$13DEC";"Fuel tank capacity";"1x1" "$100A5";"Gap recognition tolerance";"1x1" "$1009B";"Power-shift throttle angle activation threshold";"1x1" "$11DE4";"Blipper active phase maximum duration";"1x1" "$11DE6";"Blipper active phase minimum duration";"1x1" "$1009C";"Throttle angle activation threshold for blipper";"1x1" "$11DE8";"Blipper cut phase maximum duration";"1x1" "$11DEA";"Blipper cut phase minimum duration";"1x1" "$11DFC";"Injection correction factor in state blip active, gear disengage";"7x1" "$11E27";"Blipper phase gear disengage maximum duration";"5x11" "$11E96";"Vehicle speed activation threshold for blipper";"1x1" "$11EB7";"Ignition output in state blip active (when enabled)";"5x12" "$1009D";"Ignition turnoff threshold in state blip active (when enabled)";"1x1" "$11F0C";"Ignition angle in state blipper active";"11x1" "$11F37";"Injection correction factor in state blip active";"5x12" "$11FB0";"engine speed activation threshold for blipper";"1x1" "$11FB2";"Vehicle speed activation threshold for blipper";"1x1" "$11FB4";"Power-shift delay before reactivation";"1x1" "$11FB6";"Gearcut sensor error detection delay";"1x1" "$11FD3";"Ignition angle in regulate state";"5x10" "$12021";"Ignition angle in active state";"5x10" "$1205A";"Injection reduction factor in active state";"5x1" "$12075";"Injection reduction factor in state regulate";"5x10" "$1009E";"Codeword swapping of threshold logic for releasing gear cut/blipper";"1x1" "$120DA";"Power-shift break minimum engine speed";"1x1" "$120DC";"Power-shift engine speed activation threshold";"1x1" "$120DE";"Gearcut sensor threshold voltage 1";"1x1" "$120E0";"Gearcut sensor threshold voltage 2";"1x1" "$120E2";"Power-shift active phase maximum duration";"1x1" "$120E4";"Power-shift active phase minimum duration";"1x1" "$10D9C";"Gear Control Unit (GCU) used";"1x1" "$10D9C";"Gear Control Unit (GCU) used";"1x1" "$120E6";"Debounce time in state wait release";"1x1" "$10D9D";"Gear ratio first gear";"1x1" "$10D9D";"Gear ratio first gear";"1x1" "$173D8";"Gear potentiometer voltage for first gear";"1x1" "$10D9E";"Gear ratio second gear";"1x1" "$10D9E";"Gear ratio second gear";"1x1" "$173DA";"Gear potentiometer voltage for second gear";"1x1" "$10D9F";"Gear ratio third gear";"1x1" "$10D9F";"Gear ratio third gear";"1x1" "$173DC";"Gear potentiometer voltage for third gear";"1x1" "$10DA0";"Gear ratio fourth gear";"1x1" "$10DA0";"Gear ratio fourth gear";"1x1" "$173DE";"Gear potentiometer voltage for fourth gear";"1x1" "$10DA1";"Gear ratio fifth gear";"1x1" "$10DA1";"Gear ratio fifth gear";"1x1" "$173E0";"Gear potentiometer voltage for fifth gear";"1x1" "$10DA2";"Gear ratio sixth gear";"1x1" "$10DA2";"Gear ratio sixth gear";"1x1" "$173E2";"Gear potentiometer voltage for sixth gear";"1x1" "$10DB5";"Translation table gear information from gear control unit to engine control unit";"17x1" "$10058";"Power-shift error mode";"1x1" "$120E8";"Gearcut sensor error voltage, lower threshold";"1x1" "$120EA";"Gearcut sensor error voltage, upper threshold";"1x1" "$10DC6";"Gear detection over sensor only";"1x1" "$10059";"Gear detection error mode";"1x1" "$1005A";"Gear-shift lamp error mode";"1x1" "$173E4";"Gear potentiometer voltage for neutral gear";"1x1" "$10DC7";"Gear ratio recognition tolerance";"1x1" "$173E6";"Gear potentiometer voltage for neutral gear";"1x1" "$173E8";"Gear potentiometer voltage tolerance";"1x1" "$10DC8";"Gear default value in case of error";"1x1" "$173EA";"Gear detection diagnosis minimum voltage";"1x1" "$173EC";"Gear detection diagnosis maximum voltage";"1x1" "$1005B";"Ignition driver 1 error mode";"1x1" "$1005C";"Ignition driver 2 error mode";"1x1" "$1005D";"Ignition driver 3 error mode";"1x1" "$1005E";"Ignition driver 4 error mode";"1x1" "$1005F";"Ignition driver 5 error mode";"1x1" "$10060";"Ignition driver 6 error mode";"1x1" "$10061";"Ignition driver 7 error mode";"1x1" "$10062";"Ignition driver 8 error mode";"1x1" "$121DA";"Engine speed limiter soft limit ignition angle";"5x1" "$12310";"For internal use only";"1x1" "$100AE";"Ignition angle offset cylinder individuell";"10x1" "$100B8";"Ignition angle offset cylinder individuell";"10x1" "$100C2";"Ignition angle offset cylinder individuell";"10x1" "$100CC";"Ignition angle offset cylinder individuell";"10x1" "$100D6";"Ignition angle offset cylinder individuell";"10x1" "$100E0";"Ignition angle offset cylinder individuell";"10x1" "$100EA";"Ignition angle offset cylinder individuell";"10x1" "$100F4";"Ignition angle offset cylinder individuell";"10x1" "$12286";"Ignition angle during start over engine speed";"5x1" "$12292";"Ignition angle correction over engine water temperature during start";"5x1" "$1229E";"Ignition angle correction over intake air temperature";"5x1" "$122AA";"Ignition angle correction over engine water temperature";"5x1" "$100FE";"Ignition angle default map";"14x18" "$101FA";"Ignition angle default map";"14x18" "$102F6";"Ignition angle default map";"14x18" "$103F2";"Ignition angle default map";"14x18" "$104EE";"Ignition angle maximum map";"14x18" "$105EA";"Ignition angle maximum map";"14x18" "$106E6";"Ignition angle maximum map";"14x18" "$107E2";"Ignition angle maximum map";"14x18" "$108DE";"Ignition angle minimum map";"14x18" "$109DA";"Ignition angle minimum map";"14x18" "$10AD6";"Ignition angle minimum map";"14x18" "$10BD2";"Ignition angle minimum map";"14x18" "$10CCE";"Ignition angle global offset";"1x1" "$10063";"Injection driver 1 error mode";"1x1" "$10064";"Injection driver 2 error mode";"1x1" "$10065";"Injection driver 3 error mode";"1x1" "$10066";"Injection driver 4 error mode";"1x1" "$10067";"Injection driver 5 error mode";"1x1" "$10068";"Injection driver 6 error mode";"1x1" "$10069";"Injection driver 7 error mode";"1x1" "$1006A";"Injection driver 8 error mode";"1x1" "$1403E";"Injection angle over engine speed and boost pressure";"10x20" "$14112";"Injection angle during start over engine speed";"5x1" "$10D07";"Injection angle global offset";"1x1" "$10D0F";"Injection cut enable depending on gear";"1x1" "$13DAD";"Injection cut-in reduction factor";"10x1" "$13DC2";"Injection cut over maximum engine speed";"1x1" "$13DC4";"Injection cut over minimum engine speed";"1x1" "$13BDA";"Fuel enrichment minimum boost pressure gradient for activation";"1x1" "$13C12";"Fuel enrichment over engine speed and boost pressure gradient";"9x16" "$13D32";"Fuel enrichment minimum engine speed for activation";"1x1" "$1412B";"Injection disable pattern";"8x9" "$1412B";"Injection disable pattern";"8x9" "$13D49";"Fuel enrichment after injection cut-in";"20x1" "$10D0E";"Fuel enrichment after injection cut-in slow-down factor";"1x1" "$121EC";"Engine speed limiter hard limit injection cut";"5x1" "$10D08";"Injections count during start for phase 2 transition";"1x1" "$10D1A";"Knock adaptation throttle hysteresis for range change";"1x1" "$1671A";"Knock adapt throttle angle activation threshold";"10x1" "$13E00";"Knock adaptation factor (during engine dynamics)";"1x1" "$10D1B";"Knock adaptation erasing of all adaptation values";"1x1" "$13E14";"Knock adaptation engine speed/load ranges";"4x6" "$13E3A";"Knock-adaptation engine speed/load dynamic ranges";"6x1" "$13E40";"Knock-adaptation engine speed hysteresis for range change";"1x1" "$16724";"Knock adapt engine speed activation threshold";"1x1" "$10D1C";"Knock adapt engine temperature activation threshold";"1x1" "$13E42";"Knock adaptation factor (normal operation)";"1x1" "$10D1D";"CC195 integragor amplification factor initial value";"1x1" "$10D1E";"Knock control engine dynamics detection delay";"1x1" "$1673C";"Knock control engine dynamics detection threshold";"10x1" "$16766";"Knock-control minimum throttle angle";"10x1" "$1006B";"Error mode knock sensor 1";"1x1" "$1006C";"Error mode knock sensor 2";"1x1" "$1006D";"Error mode knock sensor 3";"1x1" "$1006E";"Error mode knock sensor 4";"1x1" "$13E5A";"Knock-control early shift counter upon adaptation range change";"10x1" "$13E7A";"Knock control dynamic early shift offset";"10x1" "$13E9A";"Knock control early shift counter";"10x1" "$13EBA";"Knock control early shift offset";"10x1" "$10D23";"Knock control/adaptation enable over map switch";"3x1" "$10D23";"Knock control/adaptation enable over map switch";"3x1" "$16782";"Knock chip CC195 band pass filter central frequency";"8x1" "$13EDA";"Knock control safe ignition angle upon errors";"10x1" "$13EFA";"Knock control late shift offset (upon engine dynamics)";"10x1" "$13F1A";"Knock control late shift offset maximum";"10x1" "$13F3A";"Knock control late shift offset (normal operation)";"10x1" "$1006F";"Error mode zero test knock control";"1x1" "$1678A";"Knock integral reference voltage lower threshold for switching amplification factor";"1x1" "$1678C";"Knock integral reference voltage upper threshold for switching amplification factor";"1x1" "$167A0";"Knock integral minimum reference voltage";"8x1" "$10D26";"Knock integral reference voltage diagnosis delay";"1x1" "$167C2";"Knock integral diagnosis minimum reference voltage";"8x1" "$167E4";"Knock integral diagnosis maximum reference voltage";"8x1" "$167F4";"Knock integral reference voltage filtering time constant (engine dynamics)";"1x1" "$167F6";"Knock control reference voltage initial value";"1x1" "$167F8";"Knock integral reference voltage filtering time constant (normal operation)";"1x1" "$167FA";"Knock control minimum engine speed";"1x1" "$10D30";"Knock control correspondence cylinder <-> sensor ";"8x1" "$10D38";"Knock control attached sensors";"1x1" "$167FC";"Knock control detection threshold extra factor (engine dynamics)";"1x1" "$1681A";"Knock-control detection threshold factor";"6x10" "$168AE";"Knock-control detection threshold factor";"6x10" "$16942";"Knock-control detection threshold factor";"6x10" "$169D6";"Knock-control detection threshold factor";"6x10" "$16A6A";"Knock-control detection threshold factor";"6x10" "$16AFE";"Knock-control detection threshold factor";"6x10" "$16B92";"Knock-control detection threshold factor";"6x10" "$16C26";"Knock-control detection threshold factor";"6x10" "$10D39";"Knock control minimum engine water temperature";"1x1" "$16CBA";"Knock integral sampling window begin";"6x10" "$16D0C";"Knock integral sampling window length";"10x1" "$16D16";"Knock voltage threshold for knock detection";"1x1" "$10048";"KWP2000 speed (0-old Parcomm, 1-new Parcomm from 2002)";"1x1" "$10049";"KWP2000 Inca 1 compatibility";"1x1" "$15A48";"Lambda-controller integration component factor";"6x10" "$15AC0";"Lambda-controller integration component limitation";"1x1" "$15AC2";"Lambda-controller integration component limitation";"1x1" "$15AC4";"Lambda-controller pressure after throttle plate activation threshold";"1x1" "$15AEA";"Lambda-controller proportional component factor";"6x10" "$15B62";"Lambda-controller engine speed activation threshold";"1x1" "$10D10";"Lambda-controller activation (0 ==> controller not active, 1 ==> controller active";"1x1" "$15B64";"Lambda-controller global limitation";"1x1" "$15B66";"Lambda-controller global limitation";"1x1" "$10D11";"Lambda-controller activation delay after customer function";"1x1" "$10DC9";"Lambda sensor diagnosis delay";"1x1" "$10D12";"Lambda-controller activation delay after gear-cut";"1x1" "$17406";"Lambda sensor heating PWM for LSU42";"11x1" "$17434";"Lambda sensor heating PWM for LSU49";"11x1" "$10070";"Lambda heating error mode (bank 2)";"1x1" "$10071";"Lambda heating error mode";"1x1" "$10D13";"Lambda-controller activation delay after fuel-cut";"1x1" "$10D14";"Lambda-controller activation delay after fuel-enrichment";"1x1" "$10D15";"Lambda-controller activation delay after engine speed limiting";"1x1" "$10D16";"Lambda-controller activation delay after car speed limiting";"1x1" "$10D17";"Lambda-controller activation delay after traction control action";"1x1" "$10DCA";"Typ of Lambdasensor (0 = LSU4.2 / 1 = LSU 4.9)";"1x1" "$10072";"Lambda sensor error mode (bank 2)";"1x1" "$15BC4";"Lambda default map";"20x24" "$10073";"Lambda sensor error mode";"1x1" "$10DCB";"Lambda value filtering factor";"1x1" "$17478";"Lambda linearization curve";"22x1" "$15F84";"Lambda maximum map";"20x24" "$16344";"Lambda minimum map";"20x24" "$174A4";"Lambdasensor minimum voltage";"1x1" "$174A6";"Lambdasensor maximum voltage";"1x1" "$13FEC";"Factor lapdistance forced Laptrigger";"1x1" "$13FEE";"Factor lapdistance enabeling laptrigger";"1x1" "$10DD0";"Codeword clear fastest lap";"1x1" "$13FF0";"Lap distance";"1x1" "$13FF0";"Lap distance";"1x1" "$10DD1";"Codeword display laptime difference";"1x1" "$10DD2";"Codeword clear laptimes";"1x1" "$10DD3";"Codeword polarity of laptrigger input";"1x1" "$13FF2";"Engine speed threshold for laptrigger";"1x1" "$13FF4";"Speed threshold for laptrigger";"1x1" "$10074";"Lap-trigger error mode";"1x1" "$10046";"launch function enabling through gear";"1x1" "$10E10";"launch function ignition angle offset";"11x1" "$10E30";"launch function injection disable masks";"9x1" "$10E3A";"launch function limiting value";"1x1" "$10E3C";"launch function maximum vehicle speed";"1x1" "$10DF4";"License key high word";"1x1" "$10DF6";"License key low word";"1x1" "$10D3B";"Minimum throttle angle for lifetime counter";"1x1" "$13F88";"Engine speed monitor threshold";"1x1" "$13F88";"Engine speed monitor threshold";"1x1" "$13F8A";"Engine speed monitor threshold 2";"1x1" "$13F8C";"Minimum engine speed for lifetime counter";"1x1" "$10D8C";"Map position debounce";"1x1" "$13F90";"Zero position CM channel 1";"1x1" "$13F92";"Adjusted output value CM channel 1 position 1";"1x1" "$13F94";"Adjusted output value CM channel 1 position 2";"1x1" "$13F96";"Zero position CM channel 2";"1x1" "$13F98";"Adjusted output value CM channel 2 position 1";"1x1" "$13F9A";"Adjusted output value CM channel 2 position 2";"1x1" "$13F9C";"Zero position CM channel 3";"1x1" "$13F9E";"Adjusted output value CM channel 3 position 1";"1x1" "$13FA0";"Adjusted output value CM channel 3 position 2";"1x1" "$13FA2";"Zero position CM channel 4";"1x1" "$13FA4";"Adjusted output value CM channel 4 position 1";"1x1" "$13FA6";"Adjusted output value CM channel 4 position 2";"1x1" "$13FA8";"Zero position CM channel 5";"1x1" "$13FAA";"Adjusted output value CM channel 5 position 1";"1x1" "$13FAC";"Adjusted output value CM channel 5 position 2";"1x1" "$13FAE";"Zero position CM channel 6";"1x1" "$13FB0";"Adjusted output value CM channel 6 position 1";"1x1" "$13FB2";"Adjusted output value CM channel 6 position 2";"1x1" "$13FB4";"Zero position CM channel 7";"1x1" "$13FB6";"Adjusted output value CM channel 7 position 1";"1x1" "$13FB8";"Adjusted output value CM channel 7 position 2";"1x1" "$10D8D";"MIL turn-on mode: 0-normal, 1-new errors only";"1x1" "$10D8E";"MIL minimum driving time";"1x1" "$10D8F";"MIL turn-on delay";"1x1" "$10075";"Malfunction-light special error mode";"1x1" "$10D90";"MILSPEC minimum driving time";"1x1" "$10076";"Malfunction lamp error mode";"1x1" "$13FBA";"Minimum engine speed for min/max activation";"1x1" "$10D81";"Min/max activation mode (0";"1x1" "$10CE5";"Revolution threshold for turbo-charger protection";"1x1" "$10077";"Oil lamp error mode";"1x1" "$17502";"Default value pressure in front of throttle plate in case of error";"1x1" "$10078";"Error mode pressure sensor in front of throttle plate";"1x1" "$10DD5";"Filte time constant pressure in front of throttle plate";"1x1" "$17504";"Sensor offset pressure in front of throttle plate";"1x1" "$17506";"Sensor sensitivity pressure in front of throttle plate";"1x1" "$17508";"Minimum diagnosis voltage pressure in front of throttle plate";"1x1" "$1750A";"Maximum diagnosis voltage pressure in front of throttle plate";"1x1" "$12FE6";"release threshold p22 for popoff protection";"1x1" "$12FE8";"Hysteresis threshold p22 for popoff protection";"1x1" "$12FEA";"pressure after throttle plate, given value maximum";"1x1" "$12FEC";"pressure after throttle plate, given value minimum";"1x1" "$123B4";"Boost pressure default map";"20x24" "$123B4";"Boost pressure default map";"20x24" "$12774";"Boost pressure maximum map";"20x24" "$12774";"Boost pressure maximum map";"20x24" "$12B34";"Boost pressure minimum map";"20x24" "$12B34";"Boost pressure minimum map";"20x24" "$10079";"Error mode pressure sensor in front of throttle plate";"1x1" "$17678";"Sensor offset pressure after throttle plate (Bank 2)";"1x1" "$1767A";"Sensor sensitivity pressure after throttle plate (Bank 2)";"1x1" "$10DE7";"Number of synchros for boost pressure calculation";"1x1" "$1767C";"Default value pressure after throttle plate in case of error";"1x1" "$1007A";"Error mode pressure sensor in front of throttle plate";"1x1" "$10DE8";"Filte time constant pressure after throttle plate";"1x1" "$1767E";"Sensor offset pressure after throttle plate";"1x1" "$17680";"Sensor sensitivity pressure after throttle plate";"1x1" "$17682";"Minimum diagnosis voltage pressure after throttle plate";"1x1" "$17684";"Maximum diagnosis voltage pressure after throttle plate";"1x1" "$1750C";"Ambient pressure default value in case of error";"1x1" "$1007B";"Ambient pressure error mode";"1x1" "$10DD6";"Filter time constang ambient pressure";"1x1" "$1750E";"Ambient pressure sensor offset";"1x1" "$17510";"Sensor sensitivity ambient pressure";"1x1" "$17512";"Ambient pressure minimum diagnosis voltage";"1x1" "$17514";"Ambient pressure maximum diagnosis voltage";"1x1" "$10DD7";"Sensor selection injection calculation (0=pamb / 1=p1)";"1x1" "$17516";"Crankcase pressure default value in case of error";"1x1" "$1007C";"Crankcase pressure error mode";"1x1" "$10DD8";"Filter time constant crankcase pressure";"1x1" "$17518";"Crankcase pressure sensor offset";"1x1" "$1751A";"Sensor sensitivity crankcase pressure sensor";"1x1" "$1751C";"Crankcase pressure minimum diagnosis voltage";"1x1" "$1751E";"Crankcase pressure maximum diagnosis voltage";"1x1" "$170B4";"Minimum fuel pressure threshold for MILSPEC drive";"1x1" "$17520";"Fuel pressure default value in case of error";"1x1" "$1007D";"Fuel pressure error mode";"1x1" "$10DD9";"Filter time constant fuel pressure filtering factor";"1x1" "$17522";"Fuel pressure sensor offset";"1x1" "$17524";"Sensor sensitivity fuel pressure";"1x1" "$17526";"Fuel pressure minimum diagnosis voltage";"1x1" "$17528";"Fuel pressure maximum diagnosis voltage";"1x1" "$100A6";"Minimum number engine revolutions for detecting phase signal ok";"1x1" "$170C2";"Minimum oil pressure threshold for MILSPEC drive";"5x1" "$1752A";"Engine oil default value in case of error";"1x1" "$1007E";"Engine oil pressure error mode";"1x1" "$10DDA";"Filter time constant engine oil";"1x1" "$1752C";"Engine oil sensor offset";"1x1" "$1752E";"Sensor sensitivity engine oil";"1x1" "$17530";"Engine oil pressure minimum diagnosis voltage";"1x1" "$17532";"Engine oil maximum diagnosis voltage";"1x1" "$10CE6";"popoff protection activation";"1x1" "$10040";"Manual power-fail";"1x1" "$1007F";"Error mode pressure sensor in front of throttle plate";"1x1" "$17534";"Coolant default value in case of error";"1x1" "$10080";"Error mode coolant water pressure sensor";"1x1" "$10DDB";"Filter time constang coolant pressure";"1x1" "$17536";"Coolant pressure sensor offset";"1x1" "$17538";"Sensor sensitivity coolant pressure";"1x1" "$1753A";"Coolant pressure minimum diagnosis voltage";"1x1" "$1753C";"Coolant pressure maximum diagnosis voltage";"1x1" "$10CFC";"codeword compressor in use";"1x1" "$12FEE";"Revolution threshold for backflow protection";"1x1" "$12FF0";"Revolution threshold for diaphragm protection at engine shutdown";"1x1" "$12FF2";"Threshold for diaphragm protection at low speed";"1x1" "$12FF4";"wastegate pressure, given value maximum";"1x1" "$12FF6";"wastegate pressure, given value minimum";"1x1" "$12FF8";"wastegate pressure default map";"20x24" "$133B8";"wastegate pressure maximum map";"20x24" "$13778";"wastegate pressure minimum map";"20x24" "$10DE9";"Number of synchros for wastegate pressure calculation";"1x1" "$17686";"Default value pressure for wastegate control in case of error";"1x1" "$10081";"Error mode pressure sensor wastegate";"1x1" "$10DEA";"Filte time constant wastegate pressure";"1x1" "$17688";"Sensor offset wastegate pressure";"1x1" "$1768A";"Sensor sensitivity wastegate pressure";"1x1" "$1768C";"Minimum diagnosis voltage wastegate pressure";"1x1" "$1768E";"Maximum diagnosis voltage wastegate pressure";"1x1" "$13DEE";"Static valve quantity for n-Heptan in g/min";"1x1" "$10D7F";"Read real time out of memory";"1x1" "$10041";"Clear all reset-sources";"1x1" "$10E62";"condition map for resonance flap";"10x12" "$10082";"resonace flap error mode";"1x1" "$121FA";"Engine speed limiter hard limit depending on gear";"7x1" "$12208";"Engine speed limiter igniton cut offset to hard limit";"1x1" "$12212";"Engine speed limiter soft limit depending on gear";"7x1" "$141C2";"Maximum engine speed for start phase 1";"5x1" "$12150";"Maximum engine speed";"1x1" "$12162";"Engine speed minimum recognition value";"1x1" "$10DCC";"Lambda sensor internal impedance filtering factor";"1x1" "$174A8";"Lambda sensor internal impedance offset";"1x1" "$10042";"Clear runtime minimum and maximum values";"1x1" "$1216D";"SEG_AVG_NUM";"8x1" "$10D80";"Set real time in the memory";"1x1" "$170D4";"engine speed threshold for turn on of the shift lamp";"7x1" "$170E2";"offset for turn on of the first shift LED";"1x1" "$170E4";"offset for turn on of the second shift LED";"1x1" "$170E6";"offset for turn on of the third shift LED";"1x1" "$170E8";"offset for turn on of the fourth shift LED";"1x1" "$170F2";"engine speed threshold for turn on of the shift LEDs";"7x1" "$10DDD";"Enable wheel speed of input pins";"1x1" "$10DDD";"Enable wheel speed of input pins";"1x1" "$10083";"Speed sensor front-left error mode";"1x1" "$10084";"Speed sensors front-right error mode";"1x1" "$1009F";"Speed limiter enabling through gear";"1x1" "$12122";"Speed limiter ignition angle offset";"11x1" "$12142";"Speed limiter injection disable masks";"9x1" "$1214C";"Speed limiter minimum engine speed";"1x1" "$1214E";"Speed limiter limiting value";"1x1" "$10085";"Speed sensors rear-left error mode";"1x1" "$10086";"Speed sensors rear-right error mode";"1x1" "$10DDE";"Selection of speed signal source ";"1x1" "$10DDF";"Number of teeth per front wheel revolution";"1x1" "$10DE0";"Number of teeth per rear wheel revolution";"1x1" "$10087";"Speed sensors error mode";"1x1" "$10DE1";"Filter time constant wheel speeds";"1x1" "$12176";"Engine speed lower threshold difference for start recognition";"1x1" "$1217C";"Engine speed upper threshold for normal operation recognition";"3x1" "$1004C";"Stored errors clear";"1x1" "$10EDA";"Adjustment factor tachometer";"1x1" "$10DE2";"Intake air temperature default value in case of error";"1x1" "$10088";"Intake air temperature error mode";"1x1" "$17568";"Intake air temperature linearization curve";"20x1" "$1757C";"Intake air temperature minimum diagnosis voltage";"1x1" "$1757E";"Intake air temperature maximum diagnosis voltage";"1x1" "$11634";"Acceleration dependant slip factor when dry";"10x1" "$1165E";"Acceleration dependant slip factor when wet";"10x1" "$10093";"Minimum throttle angle for traction control";"1x1" "$10094";"Selection of driven axle";"1x1" "$11679";"Traction control gear dependant P factor";"6x1" "$116A0";"ignition angle offset when dry";"12x1" "$116C6";"Traction control ignition angle offset when wet";"12x1" "$10CFD";"number of pulses per turbo revolution";"1x1" "$116FC";"injection cut pattern for traction control when dry";"20x1" "$1173A";"injection cut pattern for traction control when wet";"20x1" "$10095";"Traction control speed selection rear axle mean/minimum value";"1x1" "$11764";"Correction oversteering when dry";"10x1" "$1178E";"Correction oversteering when wet";"10x1" "$117B0";"Traction control rev. dependant P part";"6x1" "$117BC";"Minimum engine speed for traction control";"1x1" "$117C5";"Gear dependant slip offset when dry";"6x1" "$117ED";"slip map 1";"5x10" "$1186D";"slip map 10";"5x10" "$118ED";"slip map 2";"5x10" "$1196D";"slip map 3";"5x10" "$119ED";"slip map 4";"5x10" "$11A6D";"slip map 5";"5x10" "$11AED";"slip map 6";"5x10" "$11B6D";"slip map 7";"5x10" "$11BED";"slip map 8";"5x10" "$11C6D";"slip map 9";"5x10" "$11CD9";"Gear dependant slip offset when wet";"6x1" "$10096";"Default traction control switch value";"1x1" "$10089";"Error mode traction control switch";"1x1" "$10097";"TC switch minimum diagnosis voltage";"1x1" "$10098";"TC switch maximum diagnosis voltage";"1x1" "$11CE6";"Minimum vehicle speed for traction control";"1x1" "$10099";"Traction control enable";"1x1" "$12152";"Cylinder 1 TDC angle";"1x1" "$12154";"Cylinder 2 TDC angle";"1x1" "$12156";"Cylinder 3 TDC angle";"1x1" "$12158";"Cylinder 4 TDC angle";"1x1" "$1215A";"Cylinder 5 TDC angle";"1x1" "$1215C";"Cylinder 6 TDC angle";"1x1" "$1215E";"Cylinder 7 TDC angle";"1x1" "$12160";"Cylinder 8 TDC angle";"1x1" "$122C0";"Dwell time over battery voltage and engine speed";"4x6" "$122C0";"Dwell time over battery voltage and engine speed";"4x6" "$122F0";"Offset for maximum dwell time";"1x1" "$100A7";"Teeth debounce during start (teeth)";"1x1" "$100A8";"Teeth debounce during start (time)";"1x1" "$1008A";"Exhaust gases temperature error mode (bank 2)";"1x1" "$17580";"Exhaust gases temperature minimum diagnosis voltage (bank 2)";"1x1" "$17582";"Exhaust gases temperature maximum diagnosis voltage (bank 2)";"1x1" "$10DE3";"Exhaust gases temperature default value in case of error";"1x1" "$1008B";"Exhaust gases temperature error mode";"1x1" "$175A0";"Exhaust gases temperature linearization curve";"13x1" "$175AE";"Exhaust gases temperature minimum diagnosis voltage";"1x1" "$175B0";"Exhaust gases temperature maximum diagnosis voltage";"1x1" "$10DE4";"Fuel temperature default value in case of error";"1x1" "$1008C";"Fuel temperature error mode";"1x1" "$175DC";"Fuel temperature linearization curve";"20x1" "$175F0";"Fuel temperature minimum diagnosis voltage";"1x1" "$175F2";"Fuel temperature maximum diagnosis voltage";"1x1" "$141D2";"Injection duration battery correction";"5x1" "$13DD1";"Injection cut-in offset non-reduced";"10x1" "$1422A";"Injection duration factor over fuel pressure";"5x1" "$14266";"Injection duration cylinder-individual correction factor for cylinder 1";"11x10" "$14342";"Injection duration cylinder-individual correction factor for cylinder 2";"11x10" "$1441E";"Injection duration cylinder-individual correction factor for cylinder 3";"11x10" "$144FA";"Injection duration cylinder-individual correction factor for cylinder 4";"11x10" "$145D6";"Injection duration cylinder-individual correction factor for cylinder 5";"11x10" "$146B2";"Injection duration cylinder-individual correction factor for cylinder 6";"11x10" "$1478E";"Injection duration cylinder-individual correction factor for cylinder 7";"11x10" "$1486A";"Injection duration cylinder-individual correction factor for cylinder 8";"11x10" "$1497A";"Injection duration factor over engine speed and ambient pressure";"8x16" "$14A90";"Injection base duration during start";"1x1" "$14A97";"Injection duration factor over injection count during start";"4x1" "$14AAC";"Injection duration factor over ambient pressure during start";"5x1" "$14AC2";"Injection duration factor over fuel pressure during start";"5x1" "$14AD8";"Injection duration factor over engine speed during start";"5x1" "$14AE8";"Injection duration factor over engine water temperature during start (phase 1)";"5x1" "$14AF8";"Injection duration factor over engine water temperature during start (phase 2)";"5x1" "$14B08";"Injection duration factor over intake air temperature";"5x1" "$14B18";"Injection duration factor over engine water temperature";"5x1" "$14B22";"Injection duration default map";"20x24" "$14EE2";"Injection duration default map";"20x24" "$152A2";"Injection duration default map";"20x24" "$15662";"Injection duration default map";"20x24" "$15A22";"Injection duration global factor";"1x1" "$174C8";"Lambda sensor temperature linearisation curve for LSU42";"14x1" "$174F4";"Lambda sensor temperature linearisation curve for LSU49";"14x1" "$10DCD";"Lambda sensor heater diagnosis delay";"1x1" "$10DCE";"Lambda sensor minimum temperature for diagnosis";"1x1" "$10DCF";"Lambda sensor minimum operating temperature";"1x1" "$10D91";"Maximum engine temperature threshold for MILSPEC drive";"1x1" "$10DE5";"Engine water temperature default value in case of error";"1x1" "$1008D";"Engine water temperature error mode";"1x1" "$1761E";"Engine water temperature linearization curve";"20x1" "$17632";"Engine water temperature minimum diagnosis voltage";"1x1" "$17634";"Engine water temperature maximum diagnosis voltage";"1x1" "$10D92";"Maximum oil temperature threshold for MILSPEC drive";"1x1" "$10DE6";"Engine oil temperature default value in case of error";"1x1" "$1008E";"Engine water temperature error mode (bank 2)";"1x1" "$17660";"Engine oil temperature linearization curve";"20x1" "$17674";"Engine oil temperature minimum diagnosis voltage";"1x1" "$17676";"Engine oil temperature maximum diagnosis voltage";"1x1" "$178CC";"Minimum throttle angle for VVT";"1x1" "$10DEF";"codeword negation PID control bank 1";"1x1" "$10DF0";"codeword negation PID control bank 2";"1x1" "$178E0";"I factor of VVT PID-controller bank 1";"8x1" "$178F0";"Maximum I term of VVT control bank 1";"1x1" "$178F2";"Minimum I term of VVT control bank 1";"1x1" "$17906";"I factor of VVT PID-controller bank 2";"8x1" "$17916";"Maximum I term of VVT control bank 2";"1x1" "$17918";"Minimum I term of VVT control bank 2";"1x1" "$10043";"lap_b pinlayout selection switch (configurable only without VVT license)";"1x1" "$1791A";"Duty cycle for idle cam shaft position 1";"1x1" "$1791C";"Duty cycle for idle cam shaft position 2";"1x1" "$1791E";"Minimum oil pressure for VVT";"1x1" "$17920";"Duty cycle for cam shaft position 1 at maximum travel";"1x1" "$17922";"Duty cycle for cam shaft position 2 at maximum travel";"1x1" "$17936";"Camshaft position pre-control bank 1";"8x1" "$17958";"Camshaft position pre-control bank 2";"8x1" "$17968";"Frequency of VVT output signal";"1x1" "$17968";"Frequency of VVT output signal";"1x1" "$1008F";"VVT output error mode cam shaft bank 1";"1x1" "$1796A";"Maximum VVT output duty cycle bank 1";"1x1" "$1796C";"Minimum VVT output duty cycle bank 1";"1x1" "$10090";"VVT output error mode cam shaft 2";"1x1" "$1796E";"Maximum VVT output duty cycle bank 2";"1x1" "$17970";"Minimum VVT output duty cycle bank 2";"1x1" "$17972";"Minimum engine speed for VVT";"1x1" "$10DF1";"Codeword for selection between PID control strategy or on/off actuator on camshaft 1";"1x1" "$10DF2";"Codeword for selection between PID control strategy or on/off actuator on camshaft 2";"1x1" "$1797D";"D factor of VVT PID-controller dependent on oil temperature bank 1";"8x1" "$17997";"D factor of VVT PID-controller dependent on oil temperature bank 2";"8x1" "$179B1";"P factor of VVT PID-controller dependent on oil temperature bank 1";"8x1" "$179CB";"P factor of VVT PID-controller dependent on oil temperature bank 2";"8x1" "$179E3";"Battery voltage correction of VVT output bank 1";"6x1" "$179F7";"Battery voltage correction of VVT output bank 2";"6x1" "$10CFE";"wastegate adaption: threshold throttle plate position";"1x1" "$13B38";"wastegate adaption: minimum value deviation boost pressure";"1x1" "$13B3A";"wastegate adaption: maximum value deviation wastegate pressure";"1x1" "$13B3C";"wastegate adaption: maximum value of adaption offset";"1x1" "$13B3E";"wastegate adaption: minimum value of adaption offset";"1x1" "$13B40";"wastegate adaption: minimum value deviation boost pressure";"1x1" "$13B42";"wastegate adaption: engine revolution threshold";"1x1" "$13B54";"wastegate adaption: time constant of integrator";"7x1" "$13B7A";"duty cycle pressure decrease for ventilation valve";"14x1" "$13BB4";"duty cycle pressure increase for hold valve";"14x1" "$12F20";"WGPC";"12x8" "$12FE0";"WGPWMPER";"1x1" "$12FE0";"WGPWMPER";"1x1" "$12FE0";"WGPWMPER";"1x1" "$10091";"Error mode wastegate output stage";"1x1" "$10092";"Error mode wastegate output stage";"1x1" "$13FF6";"Wheel circumference front";"1x1" "$13FF6";"Wheel circumference front";"1x1" "$13FF6";"Wheel circumference front";"1x1" "$13FF6";"Wheel circumference front";"1x1" "$13FF8";"Wheel circumference rear";"1x1" "$13FF8";"Wheel circumference rear";"1x1" "$13FF8";"Wheel circumference rear";"1x1" "$12F20";"Map ""Bosch II 16""";"12x8" "$13E78";"Map ""Bosch II 16""";"5x5" "$1403E";"Map ""Bosch III 16/8""";"10x20" "$15A48";"Map ""Bosch II 16""";"6x10" "$15AEA";"Map ""Bosch II 16""";"6x10" "$17184";"Map ""Bosch II 16""";"6x11" "$1723E";"Map ""Bosch II 16""";"8x11" "$17328";"Map ""Bosch II 16""";"6x11"