Search found 56 matches
- Sat Sep 23, 2023 12:51 am
- Forum: Dev: Hardware
- Topic: Wideband Controller: Fully Custom, no ASIC!
- Replies: 211
- Views: 583067
Re: Wideband Controller: Fully Custom, no ASIC!
Is it possible to get the can address and position of the Lambda data. Reading through this thread AEM X series protocol was used. but the AEM output on a different CAN ID address 394 if im correct. Im seeing ID of 400 and 401 on this unit. also the aem is buffer 0-1 Im not seeing valid data on that...
- Mon Aug 14, 2023 10:25 am
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
Re: VSS digital input
My next question is, Why do the range of usable pins change with updates. Im using the discovery firmware, I was using PD15 as a injector the Comms LED I have set to PD12, But the latest firmware has taken away the Status LED selections and is also forcing Comms LED to PD15, even changing the INI fi...
- Sun Aug 13, 2023 12:45 am
- Forum: Dev: Software
- Topic: Unofficial RUSEFI DASH
- Replies: 35
- Views: 86246
Re: Unofficial RUSEFI DASH
your not the only one, mine fails in the compiling. I don't think you are meant to succeed because it is now a commercial product.
- Sat Aug 12, 2023 4:17 am
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
Re: VSS digital input
So after a change in the resistors, it is working. Was hoping I could have used Rusefi as a alternative on my ecu's for what is already out there, but future ecu's will work perfect. Today's goal was to get my CANBUS displays working on Rusefi. Ill also add the CANBUS wideband to the car also. https...
- Sat Aug 12, 2023 12:48 am
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
Re: VSS digital input
current limitation, on 4 digital input circuits im not using a op amp, these have a 3.3v zener diode to protect them also for over voltage, putting 12v onto one of these pins the zener will protect it and as the current is weak on the other side of the divider the zener is able to sync the voltage w...
- Fri Aug 11, 2023 4:03 pm
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
Re: VSS digital input
The selection of the voltage divider is its output is 3.3v at 5.2v and ive carried over from when I was working with teensy 3.5, 0.1v over will kill a teensy as they are not 5v tolerant at all on any pins and I haven't really until now had a problem with those values. Screen Shot 2023-08-12 at 1.50....
- Fri Aug 11, 2023 2:31 am
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
Re: VSS digital input
so the same pin on other firmware works fine on the hardware, functions perfect as a square wave 5v running through a voltage divider to 3.3v and is a floating pin. I get 3.3 volts at the processor with the pull up enabled. But rusefi it doesn't work unless I bypass the voltage divider, but bypassin...
- Wed Aug 09, 2023 12:32 pm
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
Re: VSS digital input
Ok seems to default to a pull down. I have got it working by removing my voltage divider as the resistance of that can't overcome the trigger threshold. with the 5v side the mcu pin only gets to 0.7v with the voltage divider inplace, Takes my 5v to 3.3v normally, But the pulldown is too much for the...
- Wed Aug 09, 2023 4:06 am
- Forum: Dev: Software
- Topic: VSS digital input
- Replies: 14
- Views: 24936
VSS digital input
Setting a VSS pin, What does the input expect? I have a square wave 5v VSS signal that works on the firmware I was using, But rusefi on the same hardware VSS does not work, Ive set a gauge to view the RAW data, but it doesn't trigger. I can tap the MCU pin direct with my multimeter probe and get raw...
- Mon Jul 31, 2023 7:50 am
- Forum: Dev: Hardware
- Topic: proteus iat and clt sensor drops temp when power apply
- Replies: 3
- Views: 10239
Re: proteus iat and clt sensor drops temp when power apply
Im running my own hardware, but mine does the same. I've just calibrated to the correct value when the car is running. I would say its a firmware thing and maybe to do with the voltage conversion for the battery sense on the 12v
- Mon Jul 31, 2023 6:07 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings - VVT sync requirement
So a year later. today Ive had time to test out my hardware with RusEFI. Ive noticed the cam trigger required to sync works great, Ive 100% perfect starts every time without kickback. The car drives great even in its not tuned state and feels more powerful and revy than before, it was falling flat o...
- Mon Jul 24, 2023 8:01 am
- Forum: Dev: Hardware
- Topic: Wideband Controller: Fully Custom, no ASIC!
- Replies: 211
- Views: 583067
Re: Wideband Controller: Fully Custom, no ASIC!
This is my first unit complete and tested, Basically followed instructions and got it running. Bench testing free air sits at approx 17 afr, shouldn't it be higher? with the lighter gas will drop to 13 afr and removing the gas will slowly climb and suddenly hit 20 afr and then dop back to 17 afr. Af...
- Sun Jul 09, 2023 11:47 am
- Forum: Dev: Hardware
- Topic: Wideband Controller: Fully Custom, no ASIC!
- Replies: 211
- Views: 583067
Re: Wideband Controller: Fully Custom, no ASIC!
thank you for the bin file.
My next question (and ive read the thread 10+ times and BOM) I can't find the part number for the 12 pin carrier board connector anywhere.
Can someone please tell me the part number.
My next question (and ive read the thread 10+ times and BOM) I can't find the part number for the 12 pin carrier board connector anywhere.
Can someone please tell me the part number.
- Wed Jun 07, 2023 2:54 am
- Forum: Dev: Hardware
- Topic: Wideband Controller: Fully Custom, no ASIC!
- Replies: 211
- Views: 583067
Re: Wideband Controller: Fully Custom, no ASIC!
any chance of a .bin file for this firmware, Im not a coder and can't get it to compile even watching 100 videos on how to do it, all I get is it can't find the directories after it does the bootloader section.
- Mon Jun 27, 2022 8:50 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings - VVT sync requirement
Here are 2 logs taken from today. today I have set it to paired injection and wasted COP. removed the CAM trigger pin from tuner studio pin mapping and any settings for cam trigger. trigger is set to 36/1 I am assuming this is for 36-1 or is it 36+1 cam and this is why Im having trouble? While crani...
- Sun May 22, 2022 2:09 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings - VVT sync requirement
Im working on getting logs, I don't get much of a chance to run this engine on the rusEFI as I use it as a daily, it currently runs on the "Other open firmware".
I do appreciate you guys helping too.
I do appreciate you guys helping too.
- Tue May 17, 2022 6:50 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings - VVT sync requirement
well 20% of starts is will push back on the starter when cranking.
But to my last question about the semi-sequential, i just want to get this running and drivable.
But to my last question about the semi-sequential, i just want to get this running and drivable.
- Tue May 17, 2022 2:43 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings - VVT sync requirement
So ive run the car with the modification.
Better 80% of the time.
Can i run the injection in a Semi-sequential without changing the sequential wiring? I don't want to run simultaneous, so it will fire pairs of injection?
Better 80% of the time.
Can i run the injection in a Semi-sequential without changing the sequential wiring? I don't want to run simultaneous, so it will fire pairs of injection?
- Mon May 09, 2022 10:29 pm
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings - VVT sync requirement
Thank you for adding this. Looks good on the bench test, will hopefully get time later in the week to run the engine.
- Sat Apr 23, 2022 3:57 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings
"It should not sync without cam sensor but it does" with Sequential settings My engine doesn't run good 360 degrees out for ignition. I would have thought setting Sequential would not sync until it received a valid cycle pulse from the cam. without the cycle trigger the engine can try and ...
- Sat Apr 23, 2022 2:12 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Re: Trigger settings
Ok, ive updated the firmware, with no change. Engine will sync without a cam sensor. uploaded tune file. This is not a standard board, But using STM32F407. Pins are manually configured in TS. Trigger pins are as standard rusEFI Crank PC6 Cam PA5 wired and TS Settings, Sequential injection, individua...
- Sat Apr 23, 2022 12:06 am
- Forum: Tuning Support: Making it Run
- Topic: Trigger settings - VVT sync requirement
- Replies: 24
- Views: 26683
Trigger settings - VVT sync requirement
I have a BMW M50B20 60/2 crank trigger 1 cam trigger Injection set in Tuner Studio and wired as Sequential Coils set in Tuner Studio wired as individual coils. trigger inputs PC6 and PA5 My understanding is main trigger input is Crank 60/2 PC6 Cam 1 PA5 Screen Shot 2022-04-23 at 10.03.12 am.png ECU ...
- Mon Jun 14, 2021 10:12 pm
- Forum: Dev: Software
- Topic: Configurable pins
- Replies: 9
- Views: 5965
Re: Configurable pins
The modules I currently use are 512k and is ok for the current firmware as Im using the external flash. Ive used rusefi on my older hardware, but have now updated the design. I was using the VG chip version on the old hardware I was building, but Im trying to cut down on my work load buy using pre-m...
- Mon Jun 14, 2021 8:21 am
- Forum: Dev: Software
- Topic: Configurable pins
- Replies: 9
- Views: 5965
Re: Configurable pins
Well that will solve that problem. for some reason I remembered having that as a option. My Mistake.
I was hoping to make my current hardware compatible with rusefi, But that won't be possible.
I was hoping to make my current hardware compatible with rusefi, But that won't be possible.
- Mon Jun 14, 2021 3:47 am
- Forum: Dev: Software
- Topic: Configurable pins
- Replies: 9
- Views: 5965
Re: Configurable pins
Im using external flash, i need to set the CS pin to PA15. you used to be able to select the External Flash pins, but now you can't
- Mon Jun 14, 2021 1:09 am
- Forum: Dev: Software
- Topic: Configurable pins
- Replies: 9
- Views: 5965
Configurable pins
Why has configurable pins been removed? Ive been away from rusefi for awhile and originally I was able to configure pins for functions like external flash etc (the external flash is the main one I need). I am not a programer and i don't understand the code used in rusefi, Is there one part of the fi...
- Tue Jun 30, 2020 7:58 am
- Forum: You and your build
- Topic: Connection problem with eBay board
- Replies: 30
- Views: 28830
Re: Connection problem with eBay board
ok, im using the Rusefi file rusefi.bin from the "snapshot_20200629_205450_mre-f4_rusefi.zip" file for the STM32F407, using SWD STLINK V2. and i'm doing nothing else. it will run using the USB to the rusefi console. There is no need for a bootloader and im using new blank chips.
- Mon Jun 29, 2020 1:11 am
- Forum: You and your build
- Topic: Connection problem with eBay board
- Replies: 30
- Views: 28830
Re: Connection problem with eBay board
Yes i did get that board to run, PA11,PA12 usb and PA9 to VCC, I used the Serial to upload the firmware. I didn't use a bootloader.
- Sun Jun 28, 2020 9:45 pm
- Forum: You and your build
- Topic: Connection problem with eBay board
- Replies: 30
- Views: 28830
Re: Connection problem with eBay board
Im running Rusefi and Speeduino on my STM32 F407VGT6 Boards. Native USB has been fine. Im loading the firmware on a fresh chip with SWD with a ST-Link V2 and once the firmware is installed then USB can be use. PA9 is connected to VCC. PA9 should be connected to 3.3v not 5v to be safe. STM32F407 Modu...
- Tue May 05, 2020 12:17 pm
- Forum: You and your build
- Topic: BMW m62tu
- Replies: 9
- Views: 7676
Re: BMW m62tu
Im about to do the same with a M62tu in a E39 535i, but only normally aspirated and my own design ECU.
Not having even started on the car,any idea whats not going to work once the factory ECU is removed or should i be piggy backing on to the standard system?
Not having even started on the car,any idea whats not going to work once the factory ECU is removed or should i be piggy backing on to the standard system?