rusefi.com

instant RPM is definitely telling us _something_ I think I can see uneven duration of primary rise counter? Something is not right with hardware outside or inside of ECU :( At the moment we do not log tooth ratios for wheels without a synchronization point like this 36/0 so we are a bit more blind f...

Case is finally available

i really doubt that we have such a defect.

What is the question? Would bench test buttons help?

keyword: "lazy hall" could be relevant (or not)

offtopic: randomly stumbled over Translated Funktionsrahmen Modules (10-01-2012).pdf https://github.com/rusefi/rusefi_documentation/blob/master/OEM-Docs/VAG/Translated%20Funktionsrahmen%20Modules%20(10-01-2012).pdf

3. Implement all the CAN based requests from trans, e.g. torque reduction, RPM setpoint and so on. Right now I am trying to figure out bits/bytes from the transmission are actually commanding a torque reduction Funktionsrahmen https://github.com/rusefi/rusefi_documentation/blob/master/OEM-Docs/VAG/...

They now have brand new off the shelf ECU units for under $200

Just put a few hours into Artery at32f435 port of rusEFI in a separate repo https://github.com/rusefi/fw-AT-START-F435

Makes little sense overall but to cool of an engineering challenge to pass by!

Using this board to experiment with custom board compilation outside of rusEFI primary repo https://github.com/rusefi/fw-Paralela

Similar thing just 36/0

I found the option „require cam/VVT sync for ignition“, I guess you meant to enable that? Shall I choose „Single Tooth First Half“ yes,yes you do not have two cam sensors to select "both" do you? What I already tried previously is „custom toothed wheel“ with 8/0 as I though we need to cou...

There is a chance that what you are looking for is "custom skipped 4/0" with "require cam for sync" and "first half" cam/vvt input? With a timing light to confirm offsets?

Do you keep your files on github or just locally?

Can I use my J4 header on my 0.4.8 board in as described in the the link below for the NB2 PNP adapter board to connect to a SD breakout board or does that require firmware/etc. changes too? there is a 50% change that SD card pinout has changed between 0.4.8 when it was a hack and 0.6.0 where it's ...

What zip code in OH? We have a couple of guys other there!

Welcome! v8 sounds like Proteus or https://github.com/rusefi/rusefi/wiki/Standalone-on-Demand

Can you temporary hack an injector on LS1? maybe even outside of car? and see if you click injector using LS1 while having a test config?

Looks like https://github.com/mck1117/wideband/ was not intended to be a "retail" product with documentation? I could be wrong. If you click at https://github.com/mck1117/wideband/actions and select a recent master build you would get binaries as Artifacts of github action build. Clearly t...

Poke into wires with a digital multimeter and figure out what does selecting as A/C means. I guess this initializes the pins with pull-up or something like that. Which means that you are in charge of having a pull-up of your own.

It's less important how fancy the script it's way more important to break up complex task into much smaller subtasks with clear objectives and clear results.

The script which just prints status of pins is a great step forward. Does that script behaves as expected on bench?

What board is this about?

Either way please find a much smaller script to reproduce the issue maybe just one input one test LED for output to begin with?

Whole universe of kicad vs jlc drama, I've stumbled over https://github.com/matthewlai/JLCKicadTools hopefully that would be THE answer.

yes.

WHENTHEFUNSTOPSSTOP wrote: ↑

Mon May 15, 2023 4:55 pm

no lowside inputs see it

Any chance you've only tried pin reuse inputs so far? See https://github.com/rusefi/rusefi/wiki/microRusEFI-Manual#pin-reuse

Yep.

Pictured different kia GDI harness - I've noted the twisted wires. Also a bit of tape to hold the twist in place?

On the schematics notes it says "AV6 AND AV10 ARE ANALOG since R86 and R85 are NOT populated" "AV8 AND AV9 ARE DIGITAL OUTPUTS since R30 and R84 are populated" https://github.com/rusefi/hw_microRusEfi/blob/master/gerbers/R0.6.0/micro_rusEFI.2022-04-09.csv but on bill of material ...

There are those 0R resistors which control aux input vs aux output right? Which exact channels are you trying to use as aux input?

4chan has embraced dual-side assembly and USB-C

Weird I am unable to reproduce on the laptop which was previously giving me issues. Could this whole thing be some power consumption magic or else?

Wow cool stuff I am so not there yet