rusefi.com

Thanks!

I notice one more thing, ECU tool reset to DFU seems not working.
Reset ECU and Reset to OpenBLT works.

Hi! I have questions about dual channel controller. When TS is set to can EGO sensor, wideband controller sets both heating outputs to 100% duty cycle. This is when engine is still off. In wideband controller TS both AFR0 and AFR1 changes from red no supply to green ok. This should not be that right...

This is good idea.
Does RusEfi have bounty program ready like other platforms or this has different approach?

I would like to see how this platform grow.

Hi! About Bluetooth connection. Is there any settings that should be activated for STM32F407? I have seen in code Bluetooth option enable/disable. There should be something that is slowing down communication with Bluetooth module when pins PC10/PC11 is used. Those pins are hard coded to them. Is the...

Great!

Thanks!

Hello! I have questions about RusEfi Can broadcast protocol identification. As far as I can search there isn't much information about it. RusEfi can messages is sent with id x200; x201;x202,x203;x204;x205;x206;x207;x208. Could someone please provide information what information each of ID message co...

This is great update.
I think for others users its good too.

Thanks!

This is great addition!

Great support from you!
Thanks!

Thanks for info!
And it runs great! Like very great.

Big thanks for helping!

The question is that is RusEfi runs like injector nr 1 then injector nr2 or it looks at firing order? if firing order 1-5-3-6-2-4 it will fire configurated injector nr1 then nr 5 etc. ? I'm bit confused because i was using Speeduino before and i just need to map inj like nr1 is cylinder 1 and inj2 i...

Can anyone help with this? Is RusEfi firing INJ 1,2,3,4,5,6 etc.? and I just need to configurate as my firing order?
Like if INJ 1 correspond to cyl 1 and INJ 2 correspond to cylinder 5.

Thanks!

Hi! I have question about how to pin configurate pins in RusEfi. I'm using firing order 1-5-3-6-2-4. How i should configure the pins? IGN 1,2,3 etc. and INJ 1,2,3 etc. What pins for what cylinder coil or injector should be configurate? Screenshot 2023-07-14 095919.png Screenshot 2023-07-14 095943.png

Hi! Have questions about bmw cam trigger settings. As M54 and M5x series engine uses missing tooth 60/2 on crank and poll level type for both cams. Alternative could be used single tooth cam type, this could impact egine starting if im correct. What is the basic settings for this kind of engines on ...

Maybe someone has a good running bluetooth running on RusEfi? Pin map etc.
Im not able to get ir running as it should and it seems its not posible maybe?
Could be some kind of FW bug?
Any good info will be appreciated.

Thanks!

Tried many of those settings, but still not stable communication. Tried even default values for them. Seems there is something in FW that is holding it down, sometimes run time jumps to 20 and then again drops to 0.7-5 etc. Could be other settings? Maybe RusEfi doesnt like PC10 and PC11 pins for TS?...

I tried to wire serial TTL directly to pins, but still have same slow speed, but Bluetooth even loses connection to TS.
Only PC10 and PC11 works and can't be override in TS.

Is there anything else could be done?

Hello!

I have problems to run Bluetooth on PC10/PC11 pins.
It is working, but very slow and not stable. Runtime data rate is very low 5-10 sec.

What could be the reason? I have tried other pins in TS but it's not working on other Serial ports like PA10/PA9.

Thanks!