Search found 256 matches
- Thu Jan 16, 2020 1:22 pm
- Forum: Dev: Software
- Topic: [info] rusEfi Scheduler Performance & Accuracy
- Replies: 93
- Views: 80477
Re: [info] rusEfi Scheduler Performance & Accuracy
I don't think so. If you're an OEM then you have no choice but to comply with any and all applicable standards but as a hobby yo have a lot more flexibility....as long as you've made an honest effort to go through and look at what could go wrong and addressed any that are a safety related I'd say y...
- Thu Jan 16, 2020 12:58 pm
- Forum: Dev: Software
- Topic: [info] rusEfi Scheduler Performance & Accuracy
- Replies: 93
- Views: 80477
Re: [info] rusEfi Scheduler Performance & Accuracy
Unfortunately no one of this timers can be used to decode trigger wheel. Ok, we can do SW decode. Let HW timer count tooths and start ignition/injection timer on N-th tooth. Ups, timer input has no glitch filtering. So HW timer can loose sync on noise. Ups, stm32 has no event distribution system to...
- Wed Jan 15, 2020 1:09 pm
- Forum: Dev: Software
- Topic: [info] rusEfi Scheduler Performance & Accuracy
- Replies: 93
- Views: 80477
Re: [info] rusEfi Scheduler Performance & Accuracy
From a purely safety perspective doing a FMEA would pretty much force you into finding another way to do time based control. Whether its adding a more sophisticated timer (The oem path) or just offloading critical things like ETB to a stand alone chip or unit. Safety analysis would force you to use...
- Wed Jan 15, 2020 1:02 pm
- Forum: Dev: Software
- Topic: [info] rusEfi Scheduler Performance & Accuracy
- Replies: 93
- Views: 80477
- Wed Jan 15, 2020 1:01 pm
- Forum: Dev: Software
- Topic: [info] rusEfi Scheduler Performance & Accuracy
- Replies: 93
- Views: 80477
- Tue Jan 14, 2020 8:41 am
- Forum: Dev: Software
- Topic: [info] rusEfi Scheduler Performance & Accuracy
- Replies: 93
- Views: 80477
Re: [info] rusEfi Scheduler Performance & Accuracy
The main problem is that the code uses the ST like a PC rather than as a microcontroller. If you implement input capture and output compare as it is intended then the amount of jitter you get is limited to two clock cycles because it is independant of the main processor core. Unfortunately what you ...
- Mon Jan 13, 2020 1:07 pm
- Forum: Misc
- Topic: FPGA in ECU
- Replies: 43
- Views: 50846
Re: FPGA in ECU
The STM will still consume the same power if the processing is done by the core unless you put it to sleep the programme counter will still be running and stepping through addresses. The power consumed by the FPGA will depend on how much logic is actually switching. For an engine timer you would usu...
- Tue Jan 07, 2020 11:11 am
- Forum: Dev: Hardware
- Topic: GDI: injector control options
- Replies: 19
- Views: 25150
Re: GDI: injector control options
Some A2L information here: https://www.asam.net/standards/detail/mcd-2-mc/wiki/ that includes a dll for a translator. I have used A2L files previously with CANape and CCP, I may have some more information somewhere, MATLAB has a utility that can extract data but its probably part of one of the add o...
- Tue Dec 17, 2019 1:09 pm
- Forum: Dev: Hardware
- Topic: microRusEFI
- Replies: 389
- Views: 635774
Re: microRusEfi
The tle8888 is rated for 4mj clamp energy per event. 4 injectors at 6000 RPM gives 200 injections per second (total), which at the limit of 4mj gives a total of only 0.8 watt I'm not understanding your maths, you don't seem to have added the power dissipation during the injector on period. At RDSon...
- Wed Dec 11, 2019 9:03 am
- Forum: Dev: Software
- Topic: 101 on Matlab/Simulink
- Replies: 13
- Views: 15449
Re: 101 on Matlab/Simulink
I've done some work with Matlab and Scilab, Matlab is far superior and, if you have a proper licence, then the support is very good. Code generation with Scilab is not going to be good, you can however work on algorithms and then port them to C++. You will need a good engine model or a lot of data t...
- Fri Dec 21, 2018 8:14 pm
- Forum: Dev: Hardware
- Topic: Frankenso - ECU shield compatible with OEM case / official
- Replies: 552
- Views: 594454
Re: Frankenso - ECU shield compatible with OEM case / official
Well then there is no point filtering at 1khz - you'll just get aliasing of out of band frequencies.
- Fri Dec 21, 2018 1:12 pm
- Forum: Dev: Hardware
- Topic: Frankenso - ECU shield compatible with OEM case / official
- Replies: 552
- Views: 594454
- Mon Nov 19, 2018 1:21 pm
- Forum: Misc
- Topic: $0.035 micro
- Replies: 3
- Views: 5086
Re: $0.035 micro
Up to 5cents now. Limited peripherals and no analogue channels makes them less use than a lot of other 6-pin micros.
- Sun Nov 18, 2018 12:35 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
I've lost track if what you're trying to achieve. If your throttle body accepts a PWM input to give a position then it already has a controller so you don't need a control algorithm. Are you sure that you have the PWM frequency correct?
- Wed Nov 14, 2018 8:32 am
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 354545
Re: CJ125 board
I just added the below to known_issues.txt, this functions as my reminder about what to look at when I get to look at these kinds of things. Keep the feedback coming, and thanks for the feedback that I've received. 14) Change LSU4.9 to 301 ohms, as noted here https://rusefi.com/forum/viewtopic.php?...
- Tue Nov 13, 2018 10:38 am
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 354545
Re: CJ125 board
Hello everyone, I am making my CJ125 board. I am thinking of using LSU 4.9 probes for reasons of reliability and accuracy over time. But on the pdf document bosch cj125, I saw that for the 4.9, the resistance value must be 301 ohms, out on the schematic layout of the rusefi cj125, the overall value...
- Mon Nov 12, 2018 8:08 pm
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 354545
Re: CJ125 board
I plan to get my board up and running, is there a summary of what is needed to modify a r0.2 board?
- Wed Oct 24, 2018 11:00 am
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
You need to define what you mean by 'running away', I would always expect anti-wind a motor PID-controller. The biggest problem with automotive motor controllers is the vulnerability to instability caused by transients on the supply voltage, IME that's usually dealt with by a voltage compensation mu...
- Tue Oct 23, 2018 8:04 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
2.4 ohms so low-z, even if it were high-z it would have to be PWM'd to control the speed, you won't make a position controller without a speed controller. I will measure the inductance and then I can determine the PWM frequency for the current controller.
- Mon Oct 22, 2018 6:37 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
It looks very much like this: https://patents.google.com/patent/US6173939 Checking with the multi-meter, the two pins nearest to the motor contacts are connected to those motor contacts so I have four pins for the encoder. The springs have a fair resistance to them so I would guess that the motor is...
- Mon Oct 22, 2018 6:24 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
I drilled the pop-rivets off the Mazda ETB and opened it up. Any electronics must be moulded into the top, I would guess that its all mounted on a lead frame inside the plastic. There is a magnetic encoder on the shaft for the butterfly and two contacts for the motor. It does confirm that its a Dens...
- Mon Oct 22, 2018 9:50 am
- Forum: Dev: Hardware
- Topic: Ion Sense
- Replies: 194
- Views: 215420
Re: Ion Sense
Its usually 400V fly-back from the spark that's used to charge a cap to around 80V to power the ion sense circuit. The patents are on line somewhere.
- Fri Oct 05, 2018 1:08 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
If you can post that it would help, I'm not finding any info.
- Wed Oct 03, 2018 2:25 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
The ETB that I have is from a Mazda though it is a Ford unit, quite clearly marked FoMoCo. Have you get the pinout information for these?
- Thu Sep 27, 2018 7:24 am
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
I suspect your loop timing is wrong. You can't really run a PID algorithm on a micro, its an analogue (s-domain) algorithm, on a micro you run a modified (z-domain) algorithm, in essence you have four inputs P,I,D and T where T is the loop time. There are a number of different methods to convert fro...
- Mon Sep 24, 2018 6:07 pm
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 446620
Re: electronic throttle body control ETB
Have you got any feedback from the electronic throttle? if you have then you could plot the two and try some rapid openings and then see how well the electronic throttle follows (step response). Also try some rapid voltage variations to make sure it isn't going to go unstable when you get transients.
- Tue Sep 18, 2018 9:33 pm
- Forum: Misc
- Topic: Piston coating
- Replies: 16
- Views: 20550
Re: Piston coating
There are lube additives containing teflon, slick50 is one, not quite sure how any of them would "stick" teflon to the metal of the engine, what with it being one of the most non-stick compounds we have... :lol: So that bit is probably bullshit. That SAE paper was from 1994 so it has been...
- Sat Sep 15, 2018 7:38 am
- Forum: Misc
- Topic: Piston coating
- Replies: 16
- Views: 20550
Re: Piston coating
Its OK in cooking pans as long as you don't use anything metal in them. I can't claim to do a lot of cooking but in my experience when its not a top quality pan it scratches quite easily and can peel.
- Fri Sep 14, 2018 8:25 pm
- Forum: Misc
- Topic: Piston coating
- Replies: 16
- Views: 20550
Re: Piston coating
I recall Teflon coating as well. Theory being that it's a great dry lubricant, so it helps keep things from sticking to the top of the piston and prevents these ridges from poking thought the boundary layer. The results are colder crown temperature. DuPont, the inventors, have stated that Teflon is...
- Mon Mar 19, 2018 7:50 pm
- Forum: Dev: Hardware
- Topic: Prometheus - NEW compact ECU shield!
- Replies: 160
- Views: 193793
Re: Prometheus - NEW compact ECU shield!
You don't need an op-amp for TPS or thermistors, OEM ECUs don't use them.