Search found 113 matches

by sleepingAwake
Mon Jun 21, 2021 10:36 pm
Forum: You and your build
Topic: Subaru SVX with custom RusEFI
Replies: 61
Views: 51998

Re: Subaru SVX with custom RusEFI

Holy Moly look what I've been missing.

Perhaps its time to revisit the SVX Rusefi project of my own. Thank you.
by sleepingAwake
Mon Jul 13, 2020 6:08 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

When you say "tested using console" was there a an actual Subaru IAC hooked up? Yes. It was connected. FW was running self-simulation and blipidle command was used for idle valve testing. Ok. I'll see if I can post a video showing valve position at 0-25-50-75-100% Def not acting as I expe...
by sleepingAwake
Mon Jul 13, 2020 2:42 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Hi. Sorry I had no chance to check my settings in TS. Spend whole weekend trying to create ini file for my own board. No luck. Also stuck with some strange bug with slow ADC. But I was able to validate that two-coil code is still working in master. Tested using console. You can check my settings ht...
by sleepingAwake
Mon Jul 13, 2020 1:35 am
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

I've removed the flyback diodes and the valve moves more. However it does not move in a linear fashion and makes a high pitched squeal. Sounds like the PWM signal. Also I can only close and open the valve to 50%. Can't fully open the valve regardless of manual slider %. Any particular settings I can...
by sleepingAwake
Sun Jul 12, 2020 2:30 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Just for diagnostics, if you flip the two inputs, does the valve go to full open instead of full closed? No it does not. Could it be because of the low coil resistance? 9 ohms to center tap. I would think this valve works like a seesaw. More current on one side versus the other moves the valve open...
by sleepingAwake
Sat Jul 11, 2020 8:01 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Alright that was it I needed to enable self simulation. The valve does show signs off life but goes to a fully closed position irregardless of manual IAC position changes. Does your meter show different duty cycle or voltage according to your input? Flyback diode time if you ask me. I do see a diff...
by sleepingAwake
Sat Jul 11, 2020 7:04 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Alright that was it I needed to enable self simulation.

The valve does show signs off life but goes to a fully closed position irregardless of manual IAC position changes.
by sleepingAwake
Sat Jul 11, 2020 6:17 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

AndreyB wrote:
Sat Jul 11, 2020 6:06 pm
Pictures, videos, napkin drawing of what wires go where.


Not sure whats up with the 64v gauge reading TPS in TS. Happened yesterday after updating erasing STM32 and reuploading latest firmware. It's not really on my radar right now anyway.
by sleepingAwake
Sat Jul 11, 2020 6:02 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Please spell out what is 3s lipo. There is a chance that googling what is "3s lipo" is too much effort not just for me and you are making it harder to help you by adding those extra steps. I could be very wrong here. Do we need flyback diodes here? Single-solenoid idle requires a fly back...
by sleepingAwake
Sat Jul 11, 2020 5:54 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Please spell out what is 3s lipo. There is a chance that googling what is "3s lipo" is too much effort not just for me and you are making it harder to help you by adding those extra steps. I could be very wrong here. Do we need flyback diodes here? Single-solenoid idle requires a fly back...
by sleepingAwake
Sat Jul 11, 2020 5:37 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Can you please provide any data? Can you record a video and post it on youtube of how you adjust manual idle position and how does the valve respond? what kind of power supply are you using? I could post a video. I'm using a 3s lipo to provide 12volts. When I adjust the manual IAC slider in TS and ...
by sleepingAwake
Sat Jul 11, 2020 5:31 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Is there any special settings or code that I needed to implement to get the IAC working? Really seems like a SW issue now. I have continuity from the IAC to the gates on the drivers and from the sense pins on the drivers to the pins on the STM32. Solid 12v+ on the two coils at the IAC. Do I need to...
by sleepingAwake
Sat Jul 11, 2020 3:45 pm
Forum: User Support
Topic: rusEFI online
Replies: 19
Views: 42794

Re: rusEFI online

AndreyB wrote:
Sat Jul 11, 2020 3:19 pm
Thank you for the error report! https://github.com/rusefi/web_backend/issues/66
Your welcome.
Just tried again and it worked!
by sleepingAwake
Sat Jul 11, 2020 2:53 pm
Forum: User Support
Topic: rusEFI online
Replies: 19
Views: 42794

Re: rusEFI online

Attempting to Upload the current version of my tune and the website goes to this error a few secs after pressing "upload". Fatal error: Uncaught Error: Call to undefined function array_key_first() in /homepages/5/d451478433/htdocs/online/rusefi.php:666 Stack trace: #0 /homepages/5/d4514784...
by sleepingAwake
Fri Jul 10, 2020 1:49 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Yes, no one uses this this on a real vehicle so far. I believe Dron_Gus has tested this on a bench with fix own hardware not Frankenso. I'm just bench testing at the moment as well. I just happen to have a spare IAC to test with. For testing and manual % movement in TS was it just as simple as sett...
by sleepingAwake
Fri Jul 10, 2020 12:50 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Is there any special settings or code that I needed to implement to get the IAC working?

Really seems like a SW issue now.
I have continuity from the IAC to the gates on the drivers and from the sense pins on the drivers to the pins on the STM32.
Solid 12v+ on the two coils at the IAC.
by sleepingAwake
Thu Jul 09, 2020 1:52 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Regarding voltage should I be getting 3.3volts on either pin? With the PWM set at 50% I'd expect 6v connected to a 12volt source. Looking at the schematic for Frankenso 0.4 the low side drivers output 5volts. So maybe 3.3volts is what I should expect and its not enough to drive the IAC? Low side ou...
by sleepingAwake
Thu Jul 09, 2020 12:18 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

A screenshot of the idle settings in TS would be helpful if possible. Ok. I'll do. Previously I did all configuration by code/defaults modification. I run TS for few times only. Time to learn new tricks. I'm also using mostly defaults. Of course I have to make some changes, like pin assignment and ...
by sleepingAwake
Thu Jul 09, 2020 11:37 am
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Dron_Gus wrote:
Thu Jul 09, 2020 11:31 am
I will try new FW this weekend. But I can test it only on my own HW. So I'll check that nothing is broken in SW only.
A screenshot of the idle settings in TS would be helpful if possible.
by sleepingAwake
Thu Jul 09, 2020 11:18 am
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Verified IAC functions properly when connected to a standalone PWM controller.
Nothing with RUSefi.
by sleepingAwake
Thu Jul 09, 2020 10:23 am
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

image.png This is how IAC is connected to ECU on EJ20G. I don't think think they invented something new for EG33. Actually this is the same. I connected center pin to +12 and drive open and close ends using PWM. I was able to rotate IAC from fully closed to fully opened by changing balance of duty ...
by sleepingAwake
Wed Jul 08, 2020 10:26 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Looking at the factory wiring diagram it seems I should be applying 12volts+ to the center pin and PWM ground signal to the coils.

How on earth am I going to accomplish that?
by sleepingAwake
Wed Jul 08, 2020 8:05 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Hooked up a spare SVX IAC. Using Pin PC13 and PE6 for IAC. I'm getting 3.3v on either pin and verified continuity from my harness to the gate of the responsible FET. Setup in TS to use the aforementioned pins. No errors from TS or console. When I plug in the IAC voltage drops to a few mv and nothing...
by sleepingAwake
Tue Jul 07, 2020 3:10 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

AndreyB wrote:
Tue Jul 07, 2020 3:07 pm
this is believed to be working until someone tells us it's not
Alright sounds good.
by sleepingAwake
Tue Jul 07, 2020 2:39 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Regarding control of the stock IAC in the SVX. It has 2 pins labeled OPEN and CLOSE and a third for ground. The OEM manual says to expect 6-7 volts on either power pin with key on. It looks like I'm not the only one dealing with 2 solenoid valves. This fellow ran into some issues controlling a Bosch...
by sleepingAwake
Sat Jul 04, 2020 11:07 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Thinking more about the coil and igniter setup led me on a google quest.

I found a post from someone using Megasquirt and his experience with using the default ignition settings. The igniter did not survive.

https://www.msextra.com/forums/viewtopic.php?f=104&t=40305#p294656
by sleepingAwake
Fri Jul 03, 2020 7:18 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

AndreyB wrote:
Fri Jul 03, 2020 7:04 pm
Thank you for the screenshot it's always better to have one!

I cannot explain this :( I see gppwm1_pin NONE on https://rusefi.com/online/view.php?msq=41
What does TS show for GP PWM pins?
Found it!

GP PWM 4 was set to PA0

IDK how or why

On to the next issue whatever it may be.
by sleepingAwake
Fri Jul 03, 2020 6:55 pm
Forum: You and your build
Topic: Looking for a solution for the Subaru EG33
Replies: 154
Views: 94715

Re: Looking for a solution for the Subaru EG33

Correction: auxVoltage1 and auxVoltage2 were not used and dead code, I will remove them a bit further now. Thank you for pointing me at this issue! New theory: you are not providing enough details to help you effectively. No screenshot of exact error and potentially not recent tune on REO? Please c...