Search found 47 matches
- Tue Mar 23, 2021 5:50 pm
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
Any idea ?
- Mon Mar 22, 2021 6:20 am
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
After a couple of months ! I'm trying to rerun my old engine with "frankenso" , I remember that it was a running engine. last days I was thinking why my engine is working too bad ... I guess map & fuel does not match with my engine. Here i have my logs. Unfortunately because of sanctio...
- Mon Dec 23, 2019 9:59 pm
- Forum: Dev: Software
- Topic: How to compile the firmware
- Replies: 135
- Views: 907394
Re: How to compile the firmware
I think the best compiler tool is available in linux, Just install a linux on a virtual machine like virtualbox and compile it.
As i had experience, The cygwin sometimes goes unstable especially with lib(s).
https://www.youtube.com/watch?v=H3ZQDkpKwQo
As i had experience, The cygwin sometimes goes unstable especially with lib(s).
https://www.youtube.com/watch?v=H3ZQDkpKwQo
- Sat May 26, 2018 7:02 am
- Forum: Dev: Hardware
- Topic: [SOLVED]Fatal error: angle NaN ...
- Replies: 6
- Views: 5671
Re: [SOLVED]Fatal error: angle NaN ...
After 4-5 hours -dedicated - and reading some articles, I found what just happened. The configuration of My engine was wrong. I'd tried to fully erase chip and i failed - every time - so i decided to upgrade my stlink app and chip repogrammed successfully and now ! the blue led is on. After that i p...
- Fri May 25, 2018 3:59 am
- Forum: Dev: Hardware
- Topic: [SOLVED]Fatal error: angle NaN ...
- Replies: 6
- Views: 5671
Re: Fatal error: angle NaN ...
The message belongs to two latest versions.
- Thu May 24, 2018 4:29 pm
- Forum: Dev: Hardware
- Topic: [SOLVED]Fatal error: angle NaN ...
- Replies: 6
- Views: 5671
Re: Fatal error: angle NaN ...
No i do not have scope, I checked the board without frankenstein and the error is the same.
- Thu May 24, 2018 1:23 pm
- Forum: Dev: Hardware
- Topic: [SOLVED]Fatal error: angle NaN ...
- Replies: 6
- Views: 5671
[SOLVED]Fatal error: angle NaN ...
During I was testing fuel table config on my engine, and after 10 minutes, The ecu showed critical signs. No trigger and so no ignition &| injection injectors & coils are working properly, but there is no reaction to signal cran- it is working , 3-0 volts in trigger - And i see Fatal error :...
- Tue May 08, 2018 4:33 am
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
Yes i do
- Mon May 07, 2018 7:34 pm
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
The phone was not mine and has no enough memory, so the owner decided to ... anyway , excuse me and i apologize for this.
And what a bout shutting of the engine, i did not turn the switch off or like that. The problem is ....
And what a bout shutting of the engine, i did not turn the switch off or like that. The problem is ....
- Mon May 07, 2018 4:49 pm
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
video
- Thu May 03, 2018 7:04 am
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
I'm at work for a long time and i will post a video , perhaps 3-4 days later
- Tue May 01, 2018 5:56 pm
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
Re: xu7 engine
log+conf
- Tue May 01, 2018 2:34 pm
- Forum: You and your build
- Topic: xu7 engine
- Replies: 14
- Views: 11294
xu7 engine
After some mechanical issues with ford festiva's engine, I decided to test another engine "XU7-jp4 PSA". The cranking is good and engine is working - not as good as BOSCH MP7.3 - the original ecu -, but its working. Anything is good till the throttle is closed, else the engine will shut do...
- Wed Mar 14, 2018 12:16 pm
- Forum: You and your build
- Topic: Ford Festiva / Protege / Miata motor (#3)
- Replies: 94
- Views: 66440
Re: Ford Festiva / Protege / Miata motor (#3)
I was trying to run another ford festiva - called pride here -, ignition was good but unfortunately injection and all settings about injection were not ! I'd tied to increase/decrease injection flow, injection base time, and other, and nothing has changed. - I just run TS on my laptop with new insta...
- Sat Mar 03, 2018 2:39 pm
- Forum: You and your build
- Topic: honda cbr mc17
- Replies: 4
- Views: 4920
- Sat Mar 03, 2018 10:59 am
- Forum: You and your build
- Topic: honda cbr mc17
- Replies: 4
- Views: 4920
Re: honda cbr mc17
It is 4 stroke.
Both are VR.
I guess the angle is about 90^
I had tried before with one of sensors and it was not good enough, even the crank angle was set, there was a fire in the fuel manifold.
I should mention i had tried with carburetor in that case.
Thanks
Both are VR.
I guess the angle is about 90^
I had tried before with one of sensors and it was not good enough, even the crank angle was set, there was a fire in the fuel manifold.
I should mention i had tried with carburetor in that case.
Thanks
- Fri Mar 02, 2018 9:18 pm
- Forum: You and your build
- Topic: honda cbr mc17
- Replies: 4
- Views: 4920
honda cbr mc17
Hi guys, this post will be a bout of HONDA cbr mc17 motorcycle with an engine type :mc14e, A Japanese 250 cc and 45Hp of power lovely sport bike. This bike is for 80's and as you know the EFI technique is for 90's. I decided to turn carb to efi on that bike. As you can see here http://mototh.com/fil...
- Sun Jan 28, 2018 2:43 pm
- Forum: Dev: Hardware
- Topic: Trigger issue
- Replies: 5
- Views: 5217
Re: Trigger issue
Hi again
I replaced max9926 and the issue is fixed now.
I replaced max9926 and the issue is fixed now.
- Tue Aug 29, 2017 11:50 am
- Forum: Dev: Hardware
- Topic: Trigger issue
- Replies: 5
- Views: 5217
Re: Trigger issue
I did it - if was understand correctly i should to trigger it and check the output- The output voltage - on pin 4 & 5 - is fixed on 3.34 with/without triggering. The division r network is working fine and also "r 110+106= 8.99K " - that i think it is not too bad -. VR- 's voltage is ri...
- Sun Aug 27, 2017 3:59 am
- Forum: Dev: Hardware
- Topic: Trigger issue
- Replies: 5
- Views: 5217
Trigger issue
This is a part of topic of past .... so. After some successful experience, my ecu board has some little issues. The trigger source -crank sensor - does not work anyway. I triggered it by arduino due signals in range of 10-100 Hz, but on pin A5 i have no any cganges, unfortunately i can not access to...
- Sat Aug 26, 2017 6:07 pm
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
There is no significant change even with arduino signals in max99, but the 3.3 volt on pA5
- Sat Aug 26, 2017 4:10 pm
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
Yes , R11 5k is installed.
I'm using Frankienstien v 0.11.
I had checked the output on jumpers, and i have 5 volts stable with no change even with triggering max9926/7.
Am i right ? : the voltage might be down and up when triggering .
Yes but i didn't yet, i will try it with arduino.
I'm using Frankienstien v 0.11.
I had checked the output on jumpers, and i have 5 volts stable with no change even with triggering max9926/7.
Am i right ? : the voltage might be down and up when triggering .
Yes but i didn't yet, i will try it with arduino.
- Sat Aug 26, 2017 2:37 pm
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
Yes i did some upgrades ;). I had to repair/fix some issues before starting again. I fried max9926 Unintentionally by ringing the cell phone, the cellphone had too many missed calls and it was next to a gearbox sensor. - this is what happened to my ecu, I'm trying to find out how is it possible and ...
- Sat Aug 19, 2017 4:07 am
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
This does not appear to be accurate. Your video shows TS is at 3.0.18, and the current version is 3.0.22 Please update TS to 3.0.22. snapshot526.png Can you get this to work with discovery board only? I did it before exactly. Can you get this to work with the console? Yes ! as i wrote before yes it...
- Fri Aug 18, 2017 8:23 pm
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
That's my mistake ! Bad description .... this what really my setup is : 1 stm board + Frankenstein A server with MS Windows 8 R2 data center that connected to my stm board and i upload program in to the stm by that. Some Linux & BSD machines that i have TS and Ruesfi console on theme including a...
- Fri Aug 18, 2017 5:06 am
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
Hi, The problem seems is not solved.
I can not connect with the TS.
I can not connect with the TS.
- Thu Aug 17, 2017 10:06 pm
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
Hello guys. At these links i will describe my issue. And sorry if my English is not good. So The fist link is how to compiled the source code: https://www.youtube.com/watch?v=H3ZQDkpKwQ As you can see there is no problem and done perfectly !!! in link two we have official image and issue : https://w...
- Thu Aug 17, 2017 11:31 am
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
Thank you for creating a wonderful tool ;) Yes i shared crankshaft data between my ecu and original ecu with two 220 n caps. I make sparks and car injection. Cool to see your engine running. Also good to hear you had it working stable with a native windows PC. Having the hardware working stable with...
- Thu Aug 17, 2017 3:11 am
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
I'm using discovery board + frankenstein board MS Windows is running on on a server physically connected to stm board and it was rdp. TS was/is stable before. I can fire and run an engine of ford festiva with this board+ts. (last week) [video]https://www.youtube.com/watch?v=EwkogYZi4BM[/video] Reaso...
- Wed Aug 16, 2017 7:21 pm
- Forum: Dev: Software
- Topic: Link is unstable
- Replies: 28
- Views: 19110
Re: Link is unstable
I'm so sorry for low bandwidth.
This is link:
[video]https://www.youtube.com/watch?v=oTKsmFdyY7M[/video]
This is link:
[video]https://www.youtube.com/watch?v=oTKsmFdyY7M[/video]