rusefi.com

double the hands for the moment with my engine to use it only with the sensor of the crankshaft, I used this same ecu in a 1.8t vw and it works without any problem, that dibertido, I only wanted to ask you in the configuration part of the electronic acceleration body as I set it up, I plan to use a ...

One doubt, when I gave him self-stimulation, at all times he showed me that he had an error in the timing of the crankshaft signal

I was recording a video but I saw that there are moments when there is no spark in a considerable time, I feel that it goes by the integrated I occupy. video I have some poor quality but you see the flashes of the lamp. Now I do a schematic and I attach it.

I am using a 3-way configuration to control my logic coils, with my other output processor, I occupy a 2n2907 transistor to control the logic coils I have, but with rusefí, to activate my coils, I first occupy a unified 7400, from there I occupy an IXDI604PI and finally a 2n2907, send to request a t...

my log

this is my all project.

I will check the time and upload a video. I would like to upload my tunerstudio configuration file but I can not

yes, already start with another ecu, pre-heat the engine with another ecu, the coils, work, the injectors work, but it does not start, the time I checked and it's fine, I have varied the pulse of the injectors, very low and I'm going up but it does not start, what I noticed is that when I put the ot...

I could not start it without the camshaft sensor, I'm going to try both sensors.

what trigger angle use

What else can I verify, if there is an injection, if there is a spark, what else can I see and finally, the warning in question?

with a timing light verify the trigger angle offset that was 279, made an attempt to turn on when the phase offset of the injection leave it to 279, the latter is not correct.
Finally on the phase injection map, what value can I leave to make tests?

How active is the iac control for stepper motor?

thanks

what trigger angle offset do you use

Yes, I have everything ready and the installation is without the sensor of the camshaft because I was previously occupying another computer that allowed me to work without the sensor of the camshaft.

Can you run this engine without the camshaft sensor?

I want to start my car without using a camshaft sensor, someone who can guide me?

good news....

Well, I started to solder the components to my card and I still had the same problems, until I realized that the input of my pressure sensor I left it in PB0 and activated "TEST_MODE", that was my problem from the beginning, hehehehehe, with the console, it sends in automatic "n"...

Well, with the novelty of trying another card and it worked wonders, buy the card I told kb1gtt, and it worked great, I do not know what it should be, any progress I will comment on my knowledge in electronics can be of great help.

DE OAXACA, el cable serial no es, estaba pensando realmente si era el firmware, siempre me arroja lo que subí en la foto de mi primer post, programo el release pero pareciera que fuera el debug, queria instalar una version anterior pero no encuentro ninguna.

It cost me the same, I will send one request and I will tell you my experience

buy them on ebay.

yes all leds are green

with console work fine

if it reads well, that part is well verified, in fact from 2.5 volts it takes it as a logical

the ".ini" file if it is correct.

I use a rs232 converter to ttl levels

in the photo my pcb card is appreciated, yes its native stm32f4 discovery

I occupy the MS plate, I just made a plate to use the development board.

In the other image, the ports that I use are appreciated.

in tunerstudio it appears that you are reading the controller but it remains at 4,6,10 or 14%

buen dia soy de mexico

tengo el problema de que mi placa no se conecta con tunerstudio, ya seleccioné correctamente el programa de configuracion ".ini"

solamente se conecta por "RUSEFI_CONSOLE"

monitoring the serial port this appears