Search found 11 matches
- Thu Jun 18, 2020 10:05 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
So it seems that the stm32 chip being broken is the culprit of strange reading I'm getting in tuner studio.
- Thu Jun 18, 2020 8:55 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
For clarification purposes but dose, the op-amp has inside divider ratio or are two resistors like R214/R215 does that, because at op-amp output leg I have 4.91 but after those resistors, I have 2.45. and after those resistors track goes straight to the stm32 pin
- Thu Jun 18, 2020 8:21 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
Yes changed it to 3.27 now the raw voltage dial shows around 5v, but I still have the same problem the temperature doesn't move past 50c and with nothing connected shows 8c, doesn't correspond to ohm calibration. What voltage I should be getting at an stm32 leg with a disconnected sensor? I have 2.4...
- Thu Jun 18, 2020 7:46 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
I have 3.27v on pins and in tuner studio i have 3.00.
- Thu Jun 18, 2020 7:24 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
AndreyB: Yes Frankenso without discovery, you mean this?
kb1gtt: op amp with no sensors connected have an output of 4.91v on leg 8/9 and 13/14, and at stm32 pin I haves 2.45v
kb1gtt: op amp with no sensors connected have an output of 4.91v on leg 8/9 and 13/14, and at stm32 pin I haves 2.45v
- Thu Jun 18, 2020 5:08 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
And checking the 5v rail I have 4.99v, and voltage after pull up resistor is 4.98v or at pin that clt/iat connects i have 4.98v.
- Thu Jun 18, 2020 5:00 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Re: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
A2: ecu is powered by a bench power supply 12v and amp draw is around 0.09-0.10. It is connected to a 12v-switch pin and ground connected to a big pad labeled GND near the sd card slot.
- Thu Jun 18, 2020 3:52 pm
- Forum: Dev: Hardware
- Topic: Need help with Frankenso 0.5 board, maybe short circuit or something is missing
- Replies: 14
- Views: 9182
Need help with Frankenso 0.5 board, maybe short circuit or something is missing
Short background story, while playing with sensor inputs accidentally connected 5v pin to 12v source, blew my MAX9926/TPIC8101 and some pull up/pull down resistors. Now they have been replaced but I think i have more blown parts. Question one: Can a stm ship be shorting too but still can connect to ...
- Fri Feb 22, 2019 1:12 am
- Forum: Dev: Hardware
- Topic: Help me with stm32f4
- Replies: 5
- Views: 4730
- Thu Feb 21, 2019 9:55 pm
- Forum: Dev: Hardware
- Topic: Help me with stm32f4
- Replies: 5
- Views: 4730
Re: Help me with stm32f4
Serial bootloader? https://www.st.com/en/development-tools/flasher-stm32.html Don't get your question, yes? I need to connect my pc with stm so i could programme the chip but on rusefi wiki I see that I need to place jumpers on the discovery board, but my problems is that I have directly soldered s...
- Thu Feb 21, 2019 7:23 pm
- Forum: Dev: Hardware
- Topic: Help me with stm32f4
- Replies: 5
- Views: 4730
Help me with stm32f4
Hello, I am new to this forum, got interested in rusefi when I was looking to buy ms, maybe half a year ago I bought frankenso and now I finished assembling/soldering and need your help. My problem or question is simply where do you short stm32 to program it, as my board doesn't have that stm discov...