No...
Search found 461 matches
- Tue Jun 11, 2019 4:21 am
- Forum: You and your build
- Topic: Daewoo Cielo/Nexia 1.5 DOHC #51
- Replies: 22
- Views: 19226
- Sun Jun 09, 2019 5:15 am
- Forum: You and your build
- Topic: Nissan on Frankenso #47
- Replies: 192
- Views: 139572
Re: Idling issues
The thinking goes that as the rpm's increase Rusefi should take values from idle tables for all rpm's under 750 and then take the values from normal tables for values of over 750. This does not seem to happen. As rpm's increase above 750 , 1000 or more Rusefi still seem to take values from idle tab...
- Mon Jun 03, 2019 7:20 am
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 335861
Re: CJ125 board
We don't actually gain something with starting the heater before the engine I hope you do realize that the engine can be started in an extremely cold weather conditions (like -30 degrees celsius)? And hot exhaust gases can potentially "poison" the sensor if it's not already pre-heated. Le...
- Sat Apr 13, 2019 5:13 am
- Forum: Dev: Software
- Topic: Engine control scenarios / modes
- Replies: 44
- Views: 27479
- Tue Apr 09, 2019 4:18 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
- Tue Apr 09, 2019 5:46 am
- Forum: You and your build
- Topic: Nissan on Frankenso #47
- Replies: 192
- Views: 139572
Re: Nissan on Frankenso #47
Some hints on cranking... 1) set "enable cylinder cleanup" = true * this is required for continuous failing cranking attempts, see "2)" 2) There is an alternative ( recommended? ) way to do cranking in case of problems: a) press throttle pedal to 100% (cleanup mode) b) start cran...
- Tue Apr 02, 2019 8:33 am
- Forum: You and your build
- Topic: Nissan on Frankenso #47
- Replies: 192
- Views: 139572
- Fri Mar 22, 2019 6:57 pm
- Forum: Dev: Software
- Topic: Firmware update via usb?
- Replies: 12
- Views: 8603
Re: Firmware update via usb?
Would be great!! Can you make a config for F7? Does it work from Tunerstudio with a software interrupt? The bootloader is updated and merged - please checkout and try (thank you @Russian!). I haven't tried it on F7, but you can use Prometheus configs as a starting point and change them a little... ...
- Fri Mar 22, 2019 6:54 pm
- Forum: You and your build
- Topic: Fiat Coupé 16v Turbo
- Replies: 18
- Views: 12332
Re: Fiat Coupé 16v Turbo
- Fri Mar 22, 2019 4:10 pm
- Forum: Russian Subforum
- Topic: ВАЗ-2103 "Рыжик" (1977) :: Lada 1500 "Ryzhik" (1977) #37
- Replies: 373
- Views: 390695
Re: ВАЗ-2103 "Рыжик" (1977) :: Lada 1500 "Ryzhik" (1977) #37
Выложил PR с ПИД-автокорректором оборотов ХХ по УОЗ, а также поддержкой режима настройки VE по TPS вместо MAP: https://github.com/rusefi/rusefi/pull/713 Вот пример тестовых настроек, проверенных на машине Артёма @darxfame: timingPidSettings_example.PNG P.S. Также обновил бутлоадер для Прометея, поск...
- Fri Mar 22, 2019 4:02 pm
- Forum: Dev: Hardware
- Topic: STM32F7 and STM32H7 very high performance MCUs
- Replies: 34
- Views: 25228
Re: STM32F7 and STM32H7 very high performance MCUs
Mini-F407 vs Mini-Monster-H743:
- Fri Mar 22, 2019 2:49 pm
- Forum: Dev: Software
- Topic: Firmware update via usb?
- Replies: 12
- Views: 8603
Re: Firmware update via usb?
I'll post the update for the bootloader code soon...
- Sun Mar 10, 2019 9:29 pm
- Forum: Russian Subforum
- Topic: ВАЗ-2103 "Рыжик" (1977) :: Lada 1500 "Ryzhik" (1977) #37
- Replies: 373
- Views: 390695
Re: ВАЗ-2103 "Рыжик" (1977) :: Lada 1500 "Ryzhik" (1977) #37
Сегодня был в гараже, завёл "Рыжика" и немного прогрел. Завелась с первого раза, но тут же заглохла: 20190310_1st.msl Такое происходит только на холодном движке, если хоть чуть-чуть прогреется (поработает минутку), то потом уже не глохнет после пуска. Надо будет что-то подправить в настрой...
- Fri Mar 08, 2019 12:54 pm
- Forum: Dev: Hardware
- Topic: Prometheus atempt
- Replies: 19
- Views: 13890
Re: Prometheus atempt
bluetooth module was configured previosly. but i was hopping that a ftdi adapter on tx and rx pads of BT might connect because i was afraid of cp2101 . tried to connect a osciloscope to tx and rx but comunication stops serial stops showing that stuff So it seems that Prometheus is constantly sendin...
- Fri Mar 08, 2019 7:33 am
- Forum: Dev: Hardware
- Topic: Prometheus atempt
- Replies: 19
- Views: 13890
Re: Prometheus atempt
And remember that the Bluetooth module has to be initialized first before using!
- Fri Mar 08, 2019 5:29 am
- Forum: Dev: Hardware
- Topic: Prometheus atempt
- Replies: 19
- Views: 13890
Re: Prometheus atempt
i can obseve some wierd stuff going on on serial monitor.. - Check the diodes on the bottom side of the pcb (D26,D22,D23) for polarity and shorts between. - Check the resistors R113, R114, R115. - Check the baudrate and COM port config - the default is 115200 8N1. - Don't connect to Bluetooth an US...
- Thu Mar 07, 2019 8:56 pm
- Forum: Dev: Hardware
- Topic: Prometheus atempt
- Replies: 19
- Views: 13890
Re: Prometheus atempt
it was a falty stm.. now back on track ... so connection is stablished (only without nrst wire if with nrst only hotplug mode... if conectod led turns slitly on, nrst pullup is 10k .. ) anyway i think i was able to uplod the hex , and if i hit connect im able to see it.. no connection via usb nor b...
- Mon Mar 04, 2019 10:36 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
- Sat Feb 23, 2019 5:21 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
- Sat Feb 23, 2019 4:29 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
Re: Deucalion - son of Prometheus, also a compact ECU shield!
This message is reserved for additional project info & files.
- Sat Feb 23, 2019 4:28 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
Re: Deucalion - son of Prometheus, also a compact ECU shield!
This message is reserved for additional project info & files.
- Sat Feb 23, 2019 4:28 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
Re: Deucalion - son of Prometheus, also a compact ECU shield!
This message is reserved for additional project info & files.
- Sat Feb 23, 2019 4:28 pm
- Forum: Dev: Hardware
- Topic: Deucalion - son of Prometheus, also a compact ECU shield!
- Replies: 19
- Views: 16087
Deucalion - son of Prometheus, also a compact ECU shield!
Hi there! Let me introduce our new ECU board - Deucalion ! About Deucalion... Deucalion is the son of Prometheus . An innovative easy-to-build ECU shield on rusEFI firmware. Caution! This is an experimental project at a very early development stage! More info to come... * * * deucalion_1.jpg https:/...
- Wed Feb 13, 2019 5:19 am
- Forum: Dev: Hardware
- Topic: 81 pin connector
- Replies: 3
- Views: 3317
Re: 81 pin connector
Which one does not match 121 pins footprint? Which one does or does not fit which case? The "short 81" one does not match and does not fit the ME7.8.8 case. I'd like to find the right case for it... But "medium" one does, I believe, it's closer to the 121-pin one... It's like so...
- Tue Feb 12, 2019 7:40 pm
- Forum: Dev: Hardware
- Topic: 81 pin connector
- Replies: 3
- Views: 3317
Re: 81 pin connector
There are two problems with this connector:
1) The spacing between pin rows doesn't match the 121-pin connector...
2) There are two different kinds of 81-pin connectors: And this one doesn't fit ME7.8.8 enclosure...
1) The spacing between pin rows doesn't match the 121-pin connector...
2) There are two different kinds of 81-pin connectors: And this one doesn't fit ME7.8.8 enclosure...
- Tue Feb 12, 2019 3:04 pm
- Forum: Dev: Hardware
- Topic: Prometheus - NEW compact ECU shield!
- Replies: 160
- Views: 184850
Re: Prometheus - NEW compact ECU shield!
This version compiles just fine: https://github.com/andreika-git/rusefi/tree/useTPSVETableyyj876790646 wrote: ↑Tue Feb 12, 2019 1:07 pmThanks,compile didn't succeedd but run for a long time,final error picture is attached:
- Fri Feb 08, 2019 6:20 pm
- Forum: Dev: Hardware
- Topic: let's choose an enclosure
- Replies: 121
- Views: 112866
Re: let's choose an enclosure
ME7.8.8 enclosure for 81-pin connector: IMG_20190208_144538_.jpg IMG_20190208_144545_.jpg Available new at aliexpress: https://www.aliexpress.com/item/Electronic-Control-Unit-Accessories-ECU-cover-car-engine-computer-shell-ME7-8-8-ECU-140-80/32810392033.html "Electronic Control Unit Accessories...
- Thu Feb 07, 2019 12:11 pm
- Forum: Dev: Hardware
- Topic: Prometheus - NEW compact ECU shield!
- Replies: 160
- Views: 184850
Re: Prometheus - NEW compact ECU shield!
The differences are here: https://github.com/andreika-git/prometheus/blob/master/hardware/CHANGES.TXTjekyll and hide wrote: ↑Thu Feb 07, 2019 8:01 amHi, is it possible to make a v02 board? what are the differences from v01
- Wed Feb 06, 2019 6:10 am
- Forum: Dev: Hardware
- Topic: Prometheus atempt
- Replies: 19
- Views: 13890
- Mon Feb 04, 2019 9:35 pm
- Forum: Dev: Hardware
- Topic: Prometheus atempt
- Replies: 19
- Views: 13890