rusefi.com

Do you have or can you contribute a complete list of which uaEFI pin exactly goes to which B135 B137 pin exactly? That would allow me to make a an adapter board for uaEFI.

Look what has arrived

AndreyB wrote: ↑

Mon Mar 18, 2024 4:20 pm

Please upload your tune

Please upload your tune. Looking at your logs I expect things to just work with default settings.

OEM ECU is definitely unusual.

No, it's not getting trigger errors, I do not understand the issue. Do you still have gap overrides or have you removed it?

Please upload your tune

I am not sure if current TS updater works especially in case of two units especially to update older firmware. Maybe it does maybe it does not

I would st-link just to be sure

https://github.com/rusefi/rusefi/issues/5719
https://github.com/mck1117/wideband/issues/311

I also have a question regarding Wideband. Using hellen 128, my car is running on this as a daily driver for the last 2 years at least. I would recommend starting with update of the wideband firmware. I believe that November 2023 version was a major improvement see https://github.com/mck1117/wideba...

Do you have a table of which UAEFI pin goes where?

cyrille wrote: ↑

Sun Mar 17, 2024 5:41 pm

I soldered two resistors of 4K7 ohms between VR1+ and VR1- also between VR2+ and VR2-.
The car runs very well at idle, I have not yet been driven.

https://github.com/rusefi/uaefi/issues/57

GDI gives you so much power it busts clutch lines!!!

Oh.

I am not aware of anyone fabricating rev B you would have to take it to https://github.com/mck1117/wideband/issues/310

I see some resemblance of https://github.com/mck1117/proteus/issues/124

me124 wrote: ↑

Sun Mar 17, 2024 4:00 pm

I have 10 of them assembled.

Who has assembled?

I suggest getting an uaEFI just to compare your module with uaEFI on-board module.

I see some real engineering with proper prototyping! Nice.

Ha, the black one has fuel system issues but stock ECU deals with it! We have a chance to play with closed loop range settings

opelpanfan wrote: ↑

Tue Feb 28, 2023 7:57 pm

https://github.com/opelpanfan/car-dash-wide

this is now 404 for me, is this still available anywhere?

At the moment that's DEFINITELY TOTALLY NOT THE CASE, PROCEED WITH CAUTION.

It would be off "startup times difference" topic to start discussing pull-ups etc.

Q1: I do not know. What's the purpose of CAN 1 or even what's the purpose of rusEFI?

Q2: just updated https://github.com/rusefi/rusefi/wiki/Bluetooth with references to recently updated tickets about all that

gurov wrote: ↑

Tue Mar 12, 2024 3:06 pm

hmm, perhaps once i get better gate drivers for the ignition setup on there that doesn't need to start inverted.

Ohh that's what this is all about? Ignition setup depending on start-up time seems like a signal of danger ahead.

Try running uaEFI firmware on f407disco and vice versa? A ton of compile time options are different between these two firmware one would be around https://github.com/rusefi/rusefi/commit/e8b1fc302f71a3df2162235dba02f0e3f91bf01f One day someone should add some timestamps into start-up console message...

Just improved https://github.com/rusefi/rusefi/wiki/rusEFI-calibration-via-CAN

A new concerning kind of spam happens for a couple of months now - spam posts from accounts which seem to be pretty legit like for instance https://rusefi.com/forum/memberlist.php?mode=viewprofile&u=1980 I want to assume that https://rusefi.com/forum/memberlist.php?mode=viewprofile&u=1980 is...

I note that you say "custom board (hardware)" not "custom ECU (hardware+firmware)". Cannot agree on PA0 being the best label for a pin but I guess it's a question of preference. ASIC and life-span is a risk but fully protected and diagnostics is so cool! Where do you draw the ASC...

Anyway there is also JDY-40 based on BK2461

And then there is https://www.elektroda.com/rtvforum/topic3758492.html calling all these clones of NRF24L01 ?

If anyone has an issue accessing JDY-31 using putty. 4afab98f1db9d61bbc477d42b3c4ff55.jpg It's a small world. It has Beken BK3231S chip see https://rusefi.com/forum/viewtopic.php?f=13&t=1999 where JDY was not mentioned And JDY-33 sometimes says BK3432 https://www.bekencorp.com/en/goods/detail/c...

I'd say someone with 2chan or 4chan - i.e. one of boards officially with BT - should try

See also https://forum.realdash.net/t/rusefi-ecu-support/975

Open loop would be closed loop with p=i=d=0? Looks like second step would be to set complete bias duty to different runs of same values across complete curve and see how things go? I expect a bit of randomness. Try complete curve set to -20 Try complete curve set to -10 Try complete curve set to +10...

@dbh97 has revamped the build scripts! I expect way less broken local proteus builds now.

What manual are you following? Let's fix it together, let's remove any mentioning of plugin!

https://github.com/rusefi/rusefi/wiki/rusEFI-Quick-Start-PDF

Let's try again - new release candidate https://github.com/rusefi/rusefi/releases/tag/release_20240304