rusefi.com

No, it's too many teeth and overall should be done differently. https://github.com/rusefi/rusefi/commit/036c41ecbc2d6df58faa8d8fffb66580040b37a3

I see coil operation (green)

: image.png (137.42 KiB) Viewed 2451 times

Please use rusefi.com/online for tune and logs

Is not OBD1 honda unusual in terms of using low side output to control ICM?

See https://rusefi.com/online/view.php?msq=1597&dialog=ignitionSettings

Exciting news and let von Sacher-Masoch be with you on this journey!

Dron_Gus wrote: ↑
Mon Apr 01, 2024 8:14 am
Please check Ip

It was a hardware design issue, Ip was shorted to GND

Same setup sensors are now flipped - problem stayed with second controller

: image.png (165.55 KiB) Viewed 6496 times

New log, here I only have one channel working while second one is not showing any reading.

Latest main firmware logs detailed info for both WBO channels

: image.png (161.44 KiB) Viewed 6496 times

AndreyB wrote: ↑
Sat Mar 23, 2024 5:00 pm

AndreyB wrote: ↑
Thu Mar 21, 2024 7:49 pm
fault code 5

``SensorUnderheat = 5``

is it possible to say anything from this log?

this was a cable mistake - dual-sensor cable had some wires going to wrong sensor

AndreyB wrote: ↑
Tue Mar 19, 2024 2:39 am
OEM ECU is definitely unusual.

Hold on, what are those blue things? Does this hint at CDI?

Some cool Ignition Coil Primary Voltage content

benassi124 wrote: ↑
Sat Mar 23, 2024 6:24 pm

Wire used is Tefzel wire/ M22759/32

I see some OEM harness where heater wires are thicker than signal but Dron says it should not matter.

AndreyB wrote: ↑
Thu Mar 21, 2024 7:49 pm
fault code 5

``SensorUnderheat = 5``

is it possible to say anything from this log?

vag0dr04er is teasing me so let me tease everyone else

: WhatsApp Image 2024-03-23 at 06.08.18_348ef01d.jpg (347.64 KiB) Viewed 515 times

https://github.com/rusefi/rusefi/wiki/uaEFI or https://github.com/rusefi/rusefi/wiki/Proteus-Manual depending on your attitude towards white molex, both run same exact firmware. all rusEFI units run the same exact software.

https://github.com/rusefi/rusefi/wiki/rusEFI-Quick-Start-PDF

More or less yes.

fault code 5

``SensorUnderheat = 5``

is it possible to say anything from this log?

: image.png (179.91 KiB) Viewed 7809 times

Your overrides are worse than defaults change to 14

: image.png (3.49 KiB) Viewed 5664 times

See https://github.com/rusefi/rusefi/wiki/All-Supported-Triggers#subaru-76-tooth I will also change 13 to 14 or 15

Do you have or can you contribute a complete list of which uaEFI pin exactly goes to which B135 B137 pin exactly? That would allow me to make a an adapter board for uaEFI.

Look what has arrived

: WhatsApp Image 2024-03-18 at 20.55.42_d88c6452.jpg (511.42 KiB) Viewed 10655 times

AndreyB wrote: ↑
Mon Mar 18, 2024 4:20 pm
Please upload your tune

Please upload your tune. Looking at your logs I expect things to just work with default settings.

OEM ECU is definitely unusual.

: image.png (1.53 MiB) Viewed 4382 times

No, it's not getting trigger errors, I do not understand the issue. Do you still have gap overrides or have you removed it?

Please upload your tune

: image.png (122.29 KiB) Viewed 6139 times

I am not sure if current TS updater works especially in case of two units especially to update older firmware. Maybe it does maybe it does not

I would st-link just to be sure

https://github.com/rusefi/rusefi/issues/5719
https://github.com/mck1117/wideband/issues/311

I also have a question regarding Wideband. Using hellen 128, my car is running on this as a daily driver for the last 2 years at least. I would recommend starting with update of the wideband firmware. I believe that November 2023 version was a major improvement see https://github.com/mck1117/wideba...

Do you have a table of which UAEFI pin goes where?

cyrille wrote: ↑
Sun Mar 17, 2024 5:41 pm
I soldered two resistors of 4K7 ohms between VR1+ and VR1- also between VR2+ and VR2-.
The car runs very well at idle, I have not yet been driven.

https://github.com/rusefi/uaefi/issues/57

GDI gives you so much power it busts clutch lines!!!

: WhatsApp Image 2024-03-17 at 20.07.37_629747ab.jpg (202.02 KiB) Viewed 9159 times

Oh.

I am not aware of anyone fabricating rev B you would have to take it to https://github.com/mck1117/wideband/issues/310

I see some resemblance of https://github.com/mck1117/proteus/issues/124

me124 wrote: ↑
Sun Mar 17, 2024 4:00 pm
I have 10 of them assembled.

Who has assembled?

I suggest getting an uaEFI just to compare your module with uaEFI on-board module.

rusefi.com

Search found 14331 matches

Re: Audi OEM 5-cyl trigger pattern aka "Tri-Tach"

Re: UAefi no spark

Re: UAefi no spark

Re: UAefi no spark

Re: Marquis de Sad - 1997 Mercury Grand Marquis

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Arctic Cat C-TEC2 8000 Engine

Re: Digital CDI for large engines

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Software knock processing

Re: Volvo 940 B230FK

Re: RUSEFI Android dead?

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Subaru triggers.

Re: subaru gt turbo uaefi

Re: 1994 supra with uaEFI

Re: Subaru triggers.

Re: Arctic Cat C-TEC2 8000 Engine

Re: Subaru triggers.

Re: Wideband Controller: Fully Custom, no ASIC!

Re: Wideband Controller: Fully Custom, no ASIC!

Re: subaru gt turbo uaefi

Re: subaru gt turbo uaefi

Re: 2014 red kia rio 1.6 GDI M/T busted dreams

Re: rusEFI wideband f0 modules do not work

Re: rusEFI wideband f0 modules do not work