rusefi.com

I finally found the right driver for the E-Throttle.

It is exactly the same as oem VAG, and a lot more.

Here it is:

https://no.mouser.com/ProductDetail/NXP-Freescale/MC33931VW?qs=sGAEpiMZZMvYc73DDAmzVgBNWijNCcrWnq%2f0bhIs9C8%3d

And could this be used? too many chiefs, not enough Indians :( This a relatively easy chip to learn KiCAD PCB design, would you be available to make a tiny prototype board for this chip? Yes, I can do that. Bosch units use this one, which seems to have less amps. http://www.bosch-semiconductors.com...

And could this be used?


https://no.mouser.com/datasheet/2/196/Infineon-TLE7368-DS-v02_21-EN-1109573.pdf

Thanks!

Also, do you know any IC that are identical to this?

http://www.bosch-semiconductors.com/media/automotive_systems_ics/pdf_1/ic_engine_management/bosch_ic_cy320.pdf

Think this is the same

Hi! I am looking for alternative drivers for injectors, coils, GP and ADC. Do you have any suggestions for IC's that are good, and works with rusEFI? What about something like this? Infeneon TLE6220GPAUMA2 https://www.infineon.com/dgdl/Infineon-TLE8110ED-DS-v01_00-EN.pdf?fileId=5546d46261ff577701620...

Great!

Is there any in/output you need more information on?

If so, I can find all spesifications and collect them.
The Functionsrahmen with its 5000 pages is a little heavy reading if you are unfamiliar with it

For this project, we need a can-stream between ECU, ESP, SRS Instrument etc. Can_H and Can_L It will be in format like this: (0xDA0, 0x01, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00); or (0xDA0, 0, 8, (0x01, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00)); I need some existing factors to use for the variab...

In what file should the can stream be added(Not OBD)?

We need to add some Mototsport functions. As is has e-throttle most can be done in software. Antilag can be inplemented by holding the throttle about 25% open, retard advance and lots of fuel :-) kicks in when clutch switch is open, and off when clutch released. Just need a switch input on the ecu, ...

The reason it has Rx/Tx is because it has K-line in I think. Also it does not control any functions of concerns. I Think it might be just as easy with a new board, as there will be a lot of differences. I think we should use most of the circuits, and component values from the Bosch diagrams. That wo...

Did you get Autodata?
In Engine component tesing, all the resistance and volts for all sensors are specified.

There are lots of signals in there. I think they are all discrete type signals, with the central processor as the place that keeps the security. Is it practical to simply replace the central processor? That was my first idea actually. Just make a adapter to replace the Infineon C167. But there are ...

In the A2l files there also is a lot of information.

And decompiling the hex files in IDA gives the rest

kb1gtt wrote: ↑

Sat Dec 15, 2018 3:38 pm

There are lots of signals in there. I think they are all discrete type signals, with the central processor as the place that keeps the security. Is it practical to simply replace the central processor?

That was my first idea actually.

Just make a adapter to replace the Infineon C167.

All Signals Description:

Ordered now

what is the actual size of frankenso.

Some places says 100x100, but the drawing is bigger?

Well, I dont think it is much more advanced.

I have all the files for it.

This is a export of the map list:

Also hidden in the binary says it's simple

When first making a PNP, why not make it a seller?

This is a ordinary ME7.1.

With some other stickers, 6000,-

The next step would be for me to program/set up everything to be fully working. All can messages etc. I have to test everything, and then make some maps/base maps for it on the dyno. You've missed the part that someone would have to fund the first batch of these boards - that's about $200 just for ...

For a second lets assume that the board with 121 connector is designed. What would be the next step? The next step would be for me to program/set up everything to be fully working. All can messages etc. I have to test everything, and then make some maps/base maps for it on the dyno. So after that, ...

As we now has someone that already have a working PNP, I think we should go straight to making a PCB. But this was NOT a rusEfi PNP - this was a speeduino PNP, which is a different open source project https://speeduino.com/wiki/index.php/Speeduino Making a PNP board to fit the original case is a gr...

NormanAlphaspeed wrote: ↑

Tue Dec 11, 2018 8:00 pm

Hey guys, all the mods I made are in my Github repository, https://github.com/ElDominio

All code that I added to the Speeduino firmware is in alphaMods.h (fan control mostly)
CAN code is in the CAN ME7.5 directory, hope it all helps!

Great!

As we now has someone that already have a working PNP, I think we should go straight to making a PCB. No reason to waste time and money on a frankenso, if all has been figured out with Speeduino. I have no experiense with KiCad, but if someone could help would be great. The PCB is 165 mm wide all th...

I made a PnP Speeduino for an Audi A4 1.8T, I can help with fan control (the Audi used one, idk if other VAG did), CANBUS messages (I am only missing A/C confirmation message), and well VVT is two-stage as far as I know, on and off. If I can help let me know! If I recall correctly,the 1.8T and 2.0T...

I made a PnP Speeduino for an Audi A4 1.8T, I can help with fan control (the Audi used one, idk if other VAG did), CANBUS messages (I am only missing A/C confirmation message), and well VVT is two-stage as far as I know, on and off. If I can help let me know! If I recall correctly,the 1.8T and 2.0T...

I made a PnP Speeduino for an Audi A4 1.8T, I can help with fan control (the Audi used one, idk if other VAG did), CANBUS messages (I am only missing A/C confirmation message), and well VVT is two-stage as far as I know, on and off. If I can help let me know! This would be of great help. What I am ...

I can try to get the 121 pin (ME7.5) version up and running first.

I dont need direct injection for that.

Do you have a list/package of all components needed to make everything work?

Including E-throttle, can and vvt.

Abricos wrote: ↑

Mon Dec 10, 2018 12:27 pm

https://rusefi.com/forum/viewtopic.php?f=4&t=208
https://rusefi.com/wiki/index.php?title=Hardware:OEM_121_pin_connectors

That is actually the right one for ME7