rusefi.com

Sound like I should not be using the same disk for steel. Anyway back to the Miata - here is a picture of the board set for a 1994. The wiring is 98% the same (maf vs vaf but use the same wiring, batched injection vs sequential injection). Please note that on this picture the high-side driver is set...

PS: can you please email me your mitsubishi.cpp if you made any changes, and post or email your 'showconfig' output?

The yellow one - do we want more fuel or less fuel? Anyway please try http://rusefi.com/wiki/index.php?title=Manual:Software:Fuel_Control#Fuel_control_during_cranking Green - spark - this one is more strange. I wonder if your spark signal is inverted from normal? Can you check voltage on the spark w...

Oh... But I was just mildly touching, and I try not to be on the plane with the wheel. Note taken anyway!

puff wrote:it's dangerous!

why?

ведь этот дефайн определяется не во время сборки? Ты забегаешь вперёд... Документацию... Эх, однажды :( Блин. Именно бензонасос - его логика задаётся сейчас да, во время сборки - но потом эта строчка парсится и выражение считается уже тем же механизмом, который будет парсить и считать и пользовател...

Реле бензонасоса теперь частный случай гибкой логики управления выводами:
Это приближает нас к гибко настраиваемым выводам, которыми можно будет управлять соленоидами систем изменения фаз и так далее.

fuel pump relay is now implemented as a hard-coded flexible logic general purpose output:
This gets us closer to being able to specify expressions like that one for user-defined outputs, like variable timing or whatever.

Frankenso does look bigger than I remember the stock ECU looked when I had it out about a year ago. the dimensions are actually the same - it's just the connector which is wider thus it does not work with 48 pin case. Once I am back home I'll check if it would be possible to massage the 48 case to ...

ImA4Wheelr wrote: [*]ECU Box - Used one already in the car

Probably not, sorry. See http://rusefi.com/wiki/index.php?title=Manual:Hardware:Mazda_PnP

Wow, this is looking to be an amazing thread! If you want to want to solder some outputs now, look into board testing mode feature once you have them - that would be straight forward. https://docs.google.com/spreadsheets/d/1LTvS7I-128Hft9uXHG1JrBxetVjGJDSBkySgVDQ6MGk would be pretty useful for analo...

How hard would it be to reach the connector on the actual IAC? I am curious how the OEM IAC would look like with IAC disconnected and some 10k resistor pulling the IAC line to +12. Jared please approve this test

This would tell us if the orm ECU outputs plain 0/12v PWM or more like 8/12v PWM

Just to confirm:
stock ECU idling IMG_20141004_113036.jpg
rusEfi without diode, igniton on IMG_20141006_203216.jpg
Is that right? This case we need rusEfi with diode picture just to have the full set.

There is something about clamping in the VNS14NV04 datasheet but Jared should comment. Injectors are also solenoids so they might show something similar, but injectors are usually running at lower frequency. http://i.imgur.com/MuhGEFj.png How does the car react to IAC pwm changes? Can you post the s...

jengeltx wrote:E4LB-13A359-B

Is that the side attached to the PCB or the side attached to the wires? Any logos?

you should be fine up to a v8

both boards have the same number of channels

the boards stays the same regardless of who assemble it. Frankenso SD is not functional, same with Frankenso Bluetooth - it's not functional, again - the traces on the board are not going where they should be going. yes SD is only for logging. configuration is kept inside the main chip flash memory,...

http://rusefi.com/wiki/index.php?title=Manual:Hardware_Frankenso_board has the link to https://svn.code.sf.net/p/rusefi/code/trunk/hardware/frankenso/known_issues.txt and http://rusefi.com/wiki/index.php?title=Manual:Hardware_Frankenstein_board now has a link to https://svn.code.sf.net/p/rusefi/cod...

jfive wrote:Have you tried the jim stim with one of the units yet?

Nope - I simply do not have one

this topic is about a simulator, not a stimulator. The simulator is a piece of windows software which you use without any hardware whatsoever.

The boards are pretty close, Frankenso is a newer more integrated design with some tracing issues in rev 0.1 - see http://rusefi.com/wiki/index.php?title=Hardware:For_Sale for brief a comparison on top of the page. Both boards can input analog narrow-band or wide-band, the AFR would be shown on a ga...

My point was that spending the time to do the calcs and then later changing the GPIO status to match is a waste of time I cannot agree with this point. Premature optimization is evil , at this point I'd rather focus on usability and flexibility, we should only talk performance when and if it would ...

abecedarian wrote:High-level functions that influence low-level GPIO, and thus hardware registers, no?

Sure, at the end of the day the outputs are toggled thus the registers are involved somehow

2 hours of VM&P Naphtha bath
tooth brush cleanup
2 hours of fresh VM&P Naphtha bath
tooth brush cleanup & warm soapy water
success

Sergey89 wrote:Посмотрю какие аналоги есть доступные и нарисую схему. Плату могу попробовать тоже нарисовать или кто-нибудь другой может захочет.

Никого нет Хочу схему и платку.

Должен завтра приземлиться в Питере, надеюсь кого-нить в Питере увидеть

I am going to be in Russia for the next two weeks, so I should be in bed about 3pm CST and back online around midnight in the US.

FAN and COOLANT tokens would be higher-level functions, not really related to actual hardware registers.

My connector donor has arrived. So far I am only applying mechanical forces, already pulled two pins while pulling the pieces of the PCB. Will try my favorite grinder but I am afraid to damage the pins even more. Damn silicone.

Блин, ну зачем "№;"№% загадки? Почему ты хочешь "МПЫВВМ заставить меня понять, какой чип ты считаешь новым, а какой старым?