rusefi.com

This is a 3rd generation
See also:
1st generation:


2nd generation:

Wow, these 3D printed manifolds look AMAZING! Do you plan anything made of metal for structural support considering all the vibrations? I am not a ME no idea if plastic would hold or not. I'll cast it from metal in future. It's just testing. When all will ready, i'm planning make metal copies of th...

I have a kind of success with ETB's adaptation. You can see video :slightly_smiling_face: https://youtu.be/3-yfpdf0edg Coils tested, injector tested, hall sensor tested. (By console. Not with engine) https://www.youtube.com/watch?v=dBL9Ap4UOFA https://youtu.be/uMsWpfrYtg0 I still dont have fuel pump...

Keep in mind the primary side of the coil will get to around 400V to 600V when you spark. You need insulation that can sustain this under your operating environment. AKA foggy day or cold morning with small amounts of condensation, it needs to not arc over. Sorry, i dont understand, what do you mea...

AndreyB wrote: ↑

Wed May 13, 2020 12:50 am

such low resistance probably means not smart coil?

If i understood correctly, no, it's not smart coil. They are using in LADA with carburetor and "simple", "not smart" ignition with cam and transistor or capacitor.

Hi everybody! During Slack is falling down, i decided to make post here So, what i've got now: I'm planning to test soldered by myself Frankenso in ignition control task (just ignition yet). i'll use carburetor's LADA hall sensor and ignition coil with two high voltage vire (they using in LADA 1111 ...

Hello, guys! Yesterday i tried to order Frankenso PCB ver 5.3.6 on JLCPCB and support e-mailed me about issues. That text: "Hi Sir, Well got your order with many thanks~ Sorry to bother you, but there are 2 issues that we want to confirm with you before proceeding. 1) the inner layer trace are ...

Thank you for your advice about WBO. I asked some questions my acquaintances, who understand in WBO and already ordered Innovate LC-2. How long and properly it will work, i`ll know later :D I really fear "kill" my engine and i will wait Innovate and, while it delivering by post, i`ll make ...

What's the full list of sensors you plan to run on your bike? Engine is oppozit and has air cooling (i also wanna make oil cooling, but if i will use just oil temperature sensor, ECU will not be able to have true information about temperature of every cylinder, because usually i ride with a sidecar...

You might want to take a look at the ford 1l throttle bodies, they are 40mm single ETBs and cheap and common. Oh, thank you very much for your advice, but after very long search, i founded ETB, what i need, look here: https://www.bosch-motorsport-shop.com.au/electronic-throttle-body-32mm-bore But w...

I have just one engine And I made solution, that i will start engine with intake system and WBO, because i have some fears about safety of trying to start engine without intake system and WBO...
Is innovate LC-2 good choice for my project?

Hi everybody! This is what i have now (look at the pictures) This data was recieved then engine was rotated by starter. And, despite fears, RusEFI "can see" all teeth on crank- and camshaft. That`s great! But resistors parallel to Honda VR sensors are necessary. Also, RusEFI can receive da...

So, what i have now: If you remember, i had a big problem with noises from VR-sensor on cam- and crankshaft. Every day i tried to solve this problem, make something thith that. But always had troubles. And today i just tooked two resistors, which was near my hands on my table. I don`t even know they...

Hi everybody! So, today i tried to connect console to Frankenso by micro-usb on STM32 (Usually i make it by mini-usb on Frankenso) 1. If i connect just crankshaft position sensor, console is printing, that RPM is 0. If i try to rotate engine by electric starter, RPM still be 0, i dont see nothing in...

Regarding the VR sensor - That looks like you might be able to stick a Bosch Hall sensor in the same hole as you cam sensor. What diameter is it and I will check one of the Bosch ones I have kicking about. Hello! Sorry for big delay I measured some Camshaft VR-sensor parameters: core diameter of se...

russian wrote: ↑

Thu Jul 18, 2019 12:08 am

@Kavabanga can you please reproduce this? Maybe get a new cheap VR sensor from a parts store? Shorter wires? Not sure what else could be different

Did you connected sensor by left or right channel?
You connected to console by mini-usb on Frankenso or by micro-usb on STM32?

Please turn off everything, take rear ECU cover off and take the picture of circled area of the board, maybe I have forgotten to adjust resistors? I do not understand electricity enough :( So loose wires are NOT producing noise but sensor on a stopped engine is producing noise? Weird. This is all, ...

Hi everybody! So, now i have Frankenso in my hands and i`m trying to take signal from Camshaft and crankshaft position sensor, but i have problems. In this videos i tried to explain my problem and show, what i can see in console, LCD-screen and what leds are blinking in different situations I dont k...

Regarding the VR sensor - That looks like you might be able to stick a Bosch Hall sensor in the same hole as you cam sensor. What diameter is it and I will check one of the Bosch ones I have kicking about. Thank you for information! I`ll measure it as soon is possible and tell you what diameter is ...

Hi everybody!
I used manual for compile the firmware and come to this stage....
Where i made something wrong?
Who meeted with this problem also?

mobyfab wrote: ↑

Sat Jun 29, 2019 8:31 pm

What year is the engine?

The year of engine is 2006

Camshaft position sensor

This is all, what i have:
Crankshaft position sensor

Thank you for your answers! What kind of crankshaft and camshaft position sensors installed on this engine (hall, vr)? Maybe somebody can consult me? I have electronic circuit diagram and oscillograms of crankshaft position sensor and camshaft position sensor (To see circuit diagram in normal scale,...

in the middle it is divided into two pieces... and you have on one side ETB and 2 throttle ... 11 Yamaha YZF R6r R6 Throttle Bodies Body305 That is good, but i have got oppozit engine. I need to have single ETB for once cylinder. There is no point to have one piece of Yamaha ETB with two throttles,...

Abricos wrote: ↑

Thu Jun 20, 2019 1:17 pm

What is diameter of your throttle??

Keihin carburators has 30mm throttle diameter, but injection hole on the cylinder head has 28mm diameter. I have never seen 30mm ETB. 40 is a minimum, what i seen. But, i think it is too big for one cylinder, isnt?

Oh, it`s hard to understand
How many analog inputs use this schematic on Frankenso?
I spent and spending a lot of time to learn the wiki for the board and the schematics and i still don`t understand many aspects, sorry for that questions...

Related to https://en.wikipedia.org/wiki/Dnepr_M-72? 1. I am not objective since I sell assembled Frankenso. You need to make your decision, sounds like you really need to plan your build better. Are you considering to assemble? How much soldering experience do you have? Did you ever solder SMD? 2....

how does your ignition work? magneto ? you don't have a trigger wheel and a hall sensor? minimum you need an intake manifold air temperature sensor, oxygen sensor, fuel pump, injector, throttle position potenciometor . you have air cooling of the motor? you do not have a radiator and antifreeze? ma...

Hi everybody! Now i`m trying to make my Ural motorcycle, which was made in 1981, better, much better. (DON`T ASK ME WHY, BECAUSE I DON`T KNOW! :lol: ) For example, i invented AMT system based on Arduino, which can be install on usual mechanical transmisson. (it all was started like a student project...