rusefi.com

no pullup needed ...

try different speed ... no flow control .. uppercase chars ...
https://components101.com/sites/default/files/component_datasheet/HC-05%20Datasheet.pdf

HC-08 is BLE 4.0 module ...

you need HC-05 or HC-06 Bluetooth SPP (Serial Port Protocol)

Mouser is distributor also ..

..and ... at this time, is problem to buy any kind of IC ...

(I waiting for stm32f407 .. 3 months)

Lambo97 wrote: ↑

Mon Jan 17, 2022 5:15 pm

Interesting, Soon we will be able to run Pulsejet or Turbine with Rus EFI!

Contact Colin Furze ...

..version 2.3 ...
..on the way ...

we have small talk about EGT here: https://rusefi.com/forum/viewtopic.php?p=44020#p44020

but... YES ..
two EGT channels will be useful on proteus

To Hmelik:
you need 2 wires for SPI bus .. SCLK and SO
..and one wire / line for CS# for each chip ..

...picked from SLACK ... Automotive companies avoid to use small (tiny) SMD components smallest smd (0402) can be shorted by humidity sooner ... as bigger 1206 ... I have same old ecus ..and the smallest one are 0603 ... 0805 is standard ... "bigger" caps are 1206 ... etc .. (many OEM ecus...

YES, you right ...

my meaning is wrong ... sorry for effort ...

Some cars have two 15 lines (15 and 15A) form ignition switch ..
and some has "main relay" for whole electricity in the car - drive by ECU PCM or PMU

go to DEVICE MANAGER, try to find ST Serial port (or something similar)

UNINSTALL IT AND CHECK "CHECK BOX" ..
to completely remove divers .. for .it ..

Hmmm .. good question ... And answer is NO .. No, you don't need 4 EGT sensors ... Probably you don't need any EGT sensor, when you have "STOCK TUNED" engine, with stock ECU. (or good tuned engine) Is good to have one, just for reference, when you tuning your engine, and is good to have on...

short video:
http://89.173.96.22/dohc/rusEFI/DSCN5651.AVI

..is not problem, how fast is MainRelay ON ... after ACC / IGN signal this condition is potential problem ... probably ..?? when TLE9201 is powered via 12V_MREL .. ?? 12VRelay is DOWN, when the starter is ON .. Right ....? (12V_MREL line) .. I'm assume: 12V_MREL ON - stopped engine 12V_MREL OFF - cr...

So .... 12VRelay is DOWN, when the starter is ON .. Right ....? (12V_MREL line) If the answer is YES, the E-THROTTLE is OFF, and we have no power during start / cranking - for it THEN we can't flush cyls (if we need) we can't add more air (via throttle pedal) we can't driving idle ..etc ..? I'm got ...

I'm found something "bad" .. in schema ...
(and on pcb also)

We have powered TLE9201 via 12V_MREL line..
..and ... we have NO POWER for E-Throttle WHEN we hit the starter ...

small tutorial We must pick-up CAN signal from MRE ... from R22 (for explame) twisted wire are required ... DSCN5643s.JPG then solder it to add-on board - CANH & CANL pins and we need power supply for LSU heater also.. I'm pick it from 12VMREL trace .. R139 and solder it into J21 pin (all curren...

Cпасибо.

..it is thereee..... and IT WORKS ...

SORRY ....

I'm an idiot ... ...

I still can't see EGT option in TS ...
(stable 20211114)

first one ...

...kooooonečne je to tu .... . ...

..and ask for tle9201 replacement also ..?

So, it can stay connected to GP1-GP4. Right ..?

I need help with Idle Stepper ... I'm read this https://rusefi.com/forum/viewtopic.php?f=18&t=2234 something in documentation, this page http://en.rayangyu.com/index.php?c=category&id=23 and I still have not an idea "how it works" ... Is not problem do wiring for me, but I don't kn...

Here is our "after Christmas" project.... :D It is Austin Mini, classic old tiny car "from England", cheap one. Engine is "stock" 1 liter inline 4 with Supercharger. Runs on microrusEFI, wasted spark ignition and single-port injection. Custom made 36-1 trigger wheel wit...

R470k changed from 0402 to 0603 is now complete ...
added protection diode D45 for voltage selector JP2
(when some idiot solder all 3 pads together)

..and uploaded actual version to github ...

related to: https://github.com/rusefi/hw_microRusEfi/issues/197

..the end of this story ... is here:
https://rusefi.com/forum/viewtopic.php?p=43598#p43598

it is almost done ...

Why not JLCPCB at least for passive components?

cause I have many time to solder it, by my hand ... EDITED:
and we have "logdan" also ...

updated 21.12.2021

- replaced D3 D4 D5 D6 on bottom side