Can you find resistor for pin Key and measure? I am in car without diagram. But this means gate voltage for prereg missing?
Also measure the other resistors at 8888 that shows 12v in diagram
Search found 336 matches
- Fri Jul 26, 2019 1:00 pm
- Forum: Dev: Hardware
- Topic: microRusEFI
- Replies: 388
- Views: 540991
- Fri Jul 26, 2019 11:32 am
- Forum: Dev: Hardware
- Topic: microRusEFI
- Replies: 388
- Views: 540991
Re: microRusEfi
As above, measuring those things are first step. However, the 8888 and the power supply components are REALLY hard to kill. I dont know how this is soldered and checked? Did you have it under a good microscope? Also, measure both sides of resistors at Key pin And, does the prereg or 8888 produce any...
- Sun Jul 21, 2019 4:22 am
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 335297
Re: rusEfi own wide band controller board add-on using CJ125
This manual has some interesting CJ125 info:
https://www.bosch-motorsport.com/media/downloads/ecu_ms_4_sport_turbo.pdf
From page 97-
https://www.bosch-motorsport.com/media/downloads/ecu_ms_4_sport_turbo.pdf
From page 97-
- Fri Jul 19, 2019 9:31 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
And I made it for the sensors
- Fri Jul 19, 2019 7:50 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
I would also like to add presets for ETB's, so the part-numbers/type can be in a drop down. If someone could make a initial preset would be great. (I dont know how) I would also like to add presets for injectors and sensors, as I have pages of values for anything possible. If someone could show me, ...
- Fri Jul 19, 2019 7:42 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
- Fri Jul 19, 2019 6:11 pm
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 335297
Re: rusEfi own wide band controller board add-on using CJ125
I can do that next time I test it in car.
This is the gauges showing something at bench(No sensor connected).
This is the gauges showing something at bench(No sensor connected).
- Fri Jul 19, 2019 4:02 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
A little more cleanup and changes. Scaled the factoring to be % for corrections. (% Of normal fueling) When connecting to board with this .ini, choose "use controller settings". (Actually % of cranking base fuel pulse width for some of them, dont know how to change) Started some rearrangin...
- Thu Jul 11, 2019 11:41 am
- Forum: Dev: Software
- Topic: VVT support for mote than one trigger tooth?
- Replies: 9
- Views: 7874
Re: VVT support for mote than one trigger tooth?
This should be the right values I think
http://files.s4wiki.com/docs/Audi_R4-5V_T_132kW_ME7.pdf
Page 798.
Searched: Nockenwellen
http://files.s4wiki.com/docs/Audi_R4-5V_T_132kW_ME7.pdf
Page 798.
Searched: Nockenwellen
- Thu Jul 11, 2019 11:20 am
- Forum: Dev: Software
- Topic: VVT support for mote than one trigger tooth?
- Replies: 9
- Views: 7874
Re: VVT support for mote than one trigger tooth?
It's hall.
It shows the same signal, I think the bottom one are another cam position?
It shows the same signal, I think the bottom one are another cam position?
- Thu Jul 11, 2019 3:09 am
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 371799
Re: electronic throttle body control ETB
You need to connect Dir1 and dir2 to MCU.
Select pins in TS, and use the settings in menu
Set Dis pin Low with resistor, En pin high with resistor.
You can find my schematic for it in microrusefi folder
Select pins in TS, and use the settings in menu
Set Dis pin Low with resistor, En pin high with resistor.
You can find my schematic for it in microrusefi folder
- Thu Jul 11, 2019 2:38 am
- Forum: Dev: Software
- Topic: launch control
- Replies: 100
- Views: 99819
Re: launch control
The most "important" part are to generate boost.
If you can implement ALS as well would be great.
Now with E-Throttle we dont need bypass-solenoid anymore.
One of my old air bypass setups
If you can implement ALS as well would be great.
Now with E-Throttle we dont need bypass-solenoid anymore.
One of my old air bypass setups
- Thu Jul 11, 2019 1:33 am
- Forum: Dev: Software
- Topic: electronic throttle body control ETB
- Replies: 290
- Views: 371799
- Thu Jul 11, 2019 1:30 am
- Forum: Dev: Software
- Topic: VVT support for mote than one trigger tooth?
- Replies: 9
- Views: 7874
Re: VVT support for mote than one trigger tooth?
I have VVT at the intake only.
I'll see if I find a image.
It should generate something like this:
I'll see if I find a image.
It should generate something like this:
- Wed Jul 10, 2019 10:16 pm
- Forum: Dev: Software
- Topic: VVT support for mote than one trigger tooth?
- Replies: 9
- Views: 7874
VVT support for mote than one trigger tooth?
I have a cam trigger wheel with 4 teeth. 2 short and two long.
Do you have any support for it?
I have all the data/angles etc. I think.
Do you have any support for it?
I have all the data/angles etc. I think.
- Wed Jul 10, 2019 6:58 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
Today we also got support for 1d arrays in TS.
This is very useful when tuning cold start, and work with several arrays at the same time.
This is very useful when tuning cold start, and work with several arrays at the same time.
- Wed Jul 10, 2019 1:44 pm
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 335297
Re: rusEfi own wide band controller board add-on using CJ125
Ok, didnt know. Haven't had any reaction at that gauge yet.
I'll have another look.
I'll have another look.
- Tue Jul 09, 2019 11:55 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
A new .ini with a little more fixes and more added. (Accel Enrichments + Spark Edge) EDIT: I have been uploading the file with Pin-mapping. This would be the right ones: rusefi.ini rusefi_frankenso.ini Can someone change the ignition pin mode to Falling and Rising in firmware? (Instead of default, d...
- Tue Jul 09, 2019 10:40 pm
- Forum: Dev: Hardware
- Topic: DEAD DESIGN rusEfi own wide band controller board add-on using CJ125
- Replies: 364
- Views: 335297
Re: rusEfi own wide band controller board add-on using CJ125
Are there any gauge in TS to show AFR from CJ125, or how do you do that?
I have a CJ125 up and running, but no way to show it at a gauge.
Btw, I spotted this today while making a tuningfile for a Ford Focus.
It has a lot of CJ125 settings.
I have a CJ125 up and running, but no way to show it at a gauge.
Btw, I spotted this today while making a tuningfile for a Ford Focus.
It has a lot of CJ125 settings.
- Tue Jul 09, 2019 3:06 am
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
and how to use it ??? need instruction how to used where to add this file (rusefi_refactored.ini) ??? when to add this is a file ??? Just go to File, Vehicle Projects, Project properties and select the .ini file. Or you can create new project, and load this ini instead of the .ini you normally use....
- Mon Jul 08, 2019 3:39 pm
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
I have also made some different dashboard layouts I will post here.
I am currently trying to add presets for all the most common sensors + injectors.
Here are a typical dash for tuning
I am currently trying to add presets for all the most common sensors + injectors.
Here are a typical dash for tuning
- Mon Jul 08, 2019 5:17 am
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Re: Tunerstudio Refactoring
Good!
Gp-pwm maps are among the most needed additions for this to be complete.
I have a new .ini file with more added and fully working.
Also waiting for TS to add the 1d array support to replace the curves.
Gp-pwm maps are among the most needed additions for this to be complete.
I have a new .ini file with more added and fully working.
Also waiting for TS to add the 1d array support to replace the curves.
- Sat Jul 06, 2019 11:27 am
- Forum: Dev: Software
- Topic: Tunerstudio Refactoring
- Replies: 16
- Views: 14514
Tunerstudio Refactoring
I am working at a TS refactoring, and have a .ini file here if anyone will try it out. It's far from finished, as some firmware additions/changes are required Any feedback welcome. 1.07 rusefi.ini rusefi_frankenso.ini All menus are cleaned up and grouped more rational javaw_sgQoXMie6m.png javaw_h5vu...
- Sun May 26, 2019 9:38 pm
- Forum: Dev: Hardware
- Topic: Manhattan: TLE8888 breakout board
- Replies: 34
- Views: 26302
Re: TLE8888 breakout board
Great!!
Have you tested them?
Have you tested them?
- Sat May 25, 2019 1:54 pm
- Forum: Dev: Hardware
- Topic: analog inputs: op-amp + divider - Russian - now MCP6004
- Replies: 124
- Views: 136694
Re: analog inputs: op-amp + divider - Russian - now MCP6004
I am updating the module with the right symbols now. This is just another example of what issues the hated rusefi lib does. I even used a micro usb symbol with d+ and d- switched. It's at the uart on the boards you got from me. It took me a long time to figure out.. So please follow my advice to mak...
- Sat May 25, 2019 1:34 pm
- Forum: Dev: Hardware
- Topic: analog inputs: op-amp + divider - Russian - now MCP6004
- Replies: 124
- Views: 136694
Re: analog inputs: op-amp + divider - Russian - now MCP6004
Please note all diodes needs to be soldered different. I used the frankeso symbol that has wrong pinout
- Sun May 19, 2019 3:03 am
- Forum: Dev: Hardware
- Topic: microRusEFI
- Replies: 388
- Views: 540991
- Wed May 08, 2019 4:25 pm
- Forum: Dev: Hardware
- Topic: microRusEFI
- Replies: 388
- Views: 540991
Re: microRusEfi
I think this is close to the shape ?
(No components are placed or routed)
(No components are placed or routed)
- Wed May 08, 2019 3:43 pm
- Forum: Dev: Hardware
- Topic: Common Rail MC33816/PT2001 dev board - 4 injectors GDI
- Replies: 137
- Views: 174088
Re: Common Rail MC33816 dev board - 4 injectors
Bom from the original board shows SRP1245A-100M, so that sounds close enough
- Wed May 08, 2019 3:18 pm
- Forum: Dev: Hardware
- Topic: GDI: injector control options
- Replies: 19
- Views: 23290
Re: GDI: injector control options
That's what I consider the same.
I see no reason to waste time at the MC33816, as the PT2000 are both newer and better with 6 cylinders.
I am also sure the MC33816 are soon to die out anyway.
I see no reason to waste time at the MC33816, as the PT2000 are both newer and better with 6 cylinders.
I am also sure the MC33816 are soon to die out anyway.