rusefi.com

russian wrote: ↑

Mon Jun 10, 2019 9:42 pm

Is that first rusEfi car running ITB?

No...

The thinking goes that as the rpm's increase Rusefi should take values from idle tables for all rpm's under 750 and then take the values from normal tables for values of over 750. This does not seem to happen. As rpm's increase above 750 , 1000 or more Rusefi still seem to take values from idle tab...

We don't actually gain something with starting the heater before the engine I hope you do realize that the engine can be started in an extremely cold weather conditions (like -30 degrees celsius)? And hot exhaust gases can potentially "poison" the sensor if it's not already pre-heated. Le...

russian wrote: ↑

Fri Apr 12, 2019 10:37 pm

Not supported at the moment

How about that?

RuMoDK wrote: ↑

Tue Apr 09, 2019 3:25 pm

This looks very promising. Any news?

Still work in progress, not much news, sorry...

Some hints on cranking... 1) set "enable cylinder cleanup" = true * this is required for continuous failing cranking attempts, see "2)" 2) There is an alternative ( recommended? ) way to do cranking in case of problems: a) press throttle pedal to 100% (cleanup mode) b) start cran...

russian wrote: ↑

Tue Apr 02, 2019 5:31 am

I believe that Nissan 4/360 trigger shape is not available right now. Not a huge problem

Just don't forget to check if PWM_PHASE_MAX_COUNT is enough for 360 trigger...

Would be great!! Can you make a config for F7? Does it work from Tunerstudio with a software interrupt? The bootloader is updated and merged - please checkout and try (thank you @Russian!). I haven't tried it on F7, but you can use Prometheus configs as a starting point and change them a little... ...

atntpt wrote: ↑

Fri Mar 22, 2019 12:34 pm

like baro

See https://github.com/rusefi/rusefi/pull/529
Baro should work at least partially.

Выложил PR с ПИД-автокорректором оборотов ХХ по УОЗ, а также поддержкой режима настройки VE по TPS вместо MAP: https://github.com/rusefi/rusefi/pull/713 Вот пример тестовых настроек, проверенных на машине Артёма @darxfame: timingPidSettings_example.PNG P.S. Также обновил бутлоадер для Прометея, поск...

Mini-F407 vs Mini-Monster-H743:

I'll post the update for the bootloader code soon...

Сегодня был в гараже, завёл "Рыжика" и немного прогрел. Завелась с первого раза, но тут же заглохла: 20190310_1st.msl Такое происходит только на холодном движке, если хоть чуть-чуть прогреется (поработает минутку), то потом уже не глохнет после пуска. Надо будет что-то подправить в настрой...

bluetooth module was configured previosly. but i was hopping that a ftdi adapter on tx and rx pads of BT might connect because i was afraid of cp2101 . tried to connect a osciloscope to tx and rx but comunication stops serial stops showing that stuff So it seems that Prometheus is constantly sendin...

And remember that the Bluetooth module has to be initialized first before using!

i can obseve some wierd stuff going on on serial monitor.. - Check the diodes on the bottom side of the pcb (D26,D22,D23) for polarity and shorts between. - Check the resistors R113, R114, R115. - Check the baudrate and COM port config - the default is 115200 8N1. - Don't connect to Bluetooth an US...

it was a falty stm.. now back on track ... so connection is stablished (only without nrst wire if with nrst only hotplug mode... if conectod led turns slitly on, nrst pullup is 10k .. ) anyway i think i was able to uplod the hex , and if i hit connect im able to see it.. no connection via usb nor b...

Wolfsten wrote: ↑

Mon Mar 04, 2019 9:52 pm

Damn this is what i have looking for any ideas when these come to sale? Or when files release?

Somewhere in 2019!

russian wrote: ↑

Sat Feb 23, 2019 4:41 pm

Do I see dual connector footprint?

No, of course not! It's a triple connector footprint!

Hi there! Let me introduce our new ECU board - Deucalion ! About Deucalion... Deucalion is the son of Prometheus . An innovative easy-to-build ECU shield on rusEFI firmware. Caution! This is an experimental project at a very early development stage! More info to come... * * * deucalion_1.jpg https:/...

Which one does not match 121 pins footprint? Which one does or does not fit which case? The "short 81" one does not match and does not fit the ME7.8.8 case. I'd like to find the right case for it... But "medium" one does, I believe, it's closer to the 121-pin one... It's like so...

There are two problems with this connector:
1) The spacing between pin rows doesn't match the 121-pin connector...
2) There are two different kinds of 81-pin connectors: And this one doesn't fit ME7.8.8 enclosure...

yyj876790646 wrote: ↑

Tue Feb 12, 2019 1:07 pm

Thanks,compile didn't succeedd but run for a long time,final error picture is attached:

This version compiles just fine: https://github.com/andreika-git/rusefi/tree/useTPSVETable

ME7.8.8 enclosure for 81-pin connector: IMG_20190208_144538_.jpg IMG_20190208_144545_.jpg Available new at aliexpress: https://www.aliexpress.com/item/Electronic-Control-Unit-Accessories-ECU-cover-car-engine-computer-shell-ME7-8-8-ECU-140-80/32810392033.html "Electronic Control Unit Accessories...

jekyll and hide wrote: ↑

Thu Feb 07, 2019 8:01 am

Hi, is it possible to make a v02 board? what are the differences from v01

The differences are here: https://github.com/andreika-git/prometheus/blob/master/hardware/CHANGES.TXT

atntpt wrote: ↑

Tue Feb 05, 2019 10:12 pm

I think that's okay

Try disconnecting the blue wire. I've used ST-Link/V2 programmer (clone) with only 4 wires (GND,TRST,SWCLK,SWDIO - from left to right), and it worked just fine.

P.S. And it seems that R50 is not 0.1 ohm but 1.0 ohm?

atntpt wrote: ↑

Mon Feb 04, 2019 9:26 pm

- all components on board except for some small caps 2.2uF

I've told you not to power the board until all the required small components are soldered. That's a mistake. You won't be able to run STM32 without VCAP capacitors (C19 & C42).