rusefi.com

russian wrote:

Tambralinga wrote:- FRK can not connect to Tuning Studio, Have no any signal form FRK, Discovery.

per skype troubleshooting: works in GND<>PB1 mode, does not work otherwise

Thanks to Andrey.
You can see output in this video.

[video][/video]

Mr.X

Hi ... I was test firmware latest version update on 29 Jul, 2014. The results like this... - FRK can not connect to Tuning Studio, Have no any signal form FRK, Discovery. - Port PC15 Spark1 doesn't working. We was test the FRK in test mode it OK, just working. - Port PE4 Spartk2 just working fine. A...

I am followed the Jumper. But it have no signal Can you please post a picture of your whole Frankenstein as it is now? Can you take stm32 off FRK and check the signal on the green and yellow wire when you are cranking the engine? http://i.imgur.com/t6qkCAy.jpg http://i.imgur.com/uMC9sRY.gif http://...

Do you have channels #11 & #12 connected to pins PC6 and PA5? ok JP52, JP53 use it to connect to w212, w211? How to use JP52,JP53? http://rusefi.com/images/Frankenstein/Frankenstein_v01_front_op_amp_trigger.jpg See http://rusefi.com/wiki/index.php?title=Manual:Hardware_Frankenstein_board#Step_2...

Looks like that matches the MS page, so I expect 4 pulses for Crank, and I'm not sure what to expect for a pulse for CAM. The only issue I see is that exponential decay instead of the square wave like the top signal. I think the bottom signal should look something like the red in this marked up pic...

input signal cam and crank no response with TS (RPM)
Input INP11 and INP12

for mitsubishi

Hi Andrey, I have test CRANK, CAM sensors form my car. Form Hantek 6022BE Oscilloscope. CH1 = CKP, Yellow line. CH2 = CAM, Green line. CKP Input at INP-11 CAM Input at INP-12 Sensor 4+1 In this images. Speed on 1300 rpm. http://i.imgur.com/tAXJFWH.png http://i.imgur.com/ApYkCIl.png http://i.imgur.co...

ok

JP52, JP53 use it to connect to w212, w211?
How to use JP52,JP53?

I will set the ts for the crank and cam 4/1 hall sensor
How is the test signals cam / crank?

I was test the firmware Rev.4048. - It have no LED status. The blue LED has to blink. If it does not blink then something bad is going on - see http://rusefi.com/wiki/index.php?title=Manual:Software:User/en#LEDs Let's figure this out. Can you please connect to dev console port with dev console? Doe...

Hi, Man

I was test the firmware Rev.4048.
- It have no LED status.


- The stm32 is lack when I burn some value in Tuning Studio.
Please see the video.
[video][/video]

Thanks.
Mr.X

Hi Andrey. Regarding to latest version, I've test injector connect to LED it still lighting (Not blinking). Then, I was test firmware in the older version like Rev.3349. The injector still working good as clip video. [video]http://youtu.be/rEslMzc-JXk[/video] And pulses like... http://i.imgur.com/6C...

I have problem to connect to the real Injector with stm32. Just do it via dev console. 1) showconfig - does it show the right pin for the injector? It is like this img.... http://i.imgur.com/HP4R72C.gif 2) digiral sniffer - does it show injection pulses? That is http://i.imgur.com/yoaJn4g.gif Thanks...

Thanks for the great answers.

Help on how to test the injectors to test it.
because Injectors not working
for 4 injectors( 12v. to injector+ ) (injector GND to INJ-12)

new firmware

port TTL usb PC10,PC11 Jump GND to PB1 putty display



port TTL usb PC10,PC11 remove GND to PB1 putty display



Why port TTL no respond 'Alive'?
no connect to Ts

micro usb on board stm32 can connect TS ok port respond 'Alive'

port TTL usb PC10,PC11 not ok have respond in picture(put jumper GND to pin PB1)



port uart putty no response

http://www.youtube.com/watch?v=Tt3HtRRtWtY In this test case we connect STM32 Discovery and ECU simulator (The voltage developed by the VR sensor) to Tuning Studio over serial port. First time success, The STM32 Discovery coding by to read the values form VR sensor and send the data to serial port a...

i can open TS by not need program simulator?

The new one images. kidding project.

FK Board.

Sim Board.


Thanks,
Mr.X

Skype Id : Shiva-p

Help me please
I connect analog tps clt Tunestudio unresponsive .
TPS = PA0
CLT = PA1
I'm not sure what to do.
I want pin out for Frankenstein and setting Tunestudio
Thank you

TunerStudio cann't setting Direct coil , vtec and boots control for 4 cylinder.
How to setting and firmware setting?

Good. Glad to be of assistance. I see your additions so I'll play around with them. I've also written up a bit of a ".hex file loading cheat sheet" for my own use, but maybe it could be incorporated into some more comprehensive instructions. How to get and load the latest rusEFI .hex file...