rusefi.com

russian wrote:

Tambralinga wrote:I try to reflash default ford aspine connect to TS led red show.
If disconect TS and reboot led red not show.

Are you using latest rusefi.ini file? Let me try all this at home later today and we would need to try it via teamviewer maybe.

Yes latest rusefi.ini.

Firmware update 18-11-2014( set_engine_type 16) connect to TS led red show. How is it after reboot? There is a known issue with crash on config write - https://sourceforge.net/p/rusefi/tickets/114/ - restart is the current work-around. What's on the LCD screen? I try to reflash default ford aspine ...

Firmware update 18-11-2014( set_engine_type 16) connect to TS led red show.

kb1gtt wrote:Are pins 1-3 = 66 ohms and 4 - 6 = 66 ohms?

I have had a hardware plan for supporting steppers. I'll see if russian is on board with my plan. I think we'll have stepper support shortly. Can you take these ohm readings and let me know if they are 66 ohms?

Yes 66 ohm.

puff wrote:neat! seams there is InelliJ for Mac!

don't know tho why would I need it

How can I run on Mac osx Lion (7.5), Could you please me how it is step ??
Thanks
;-x

Additional for a beginners guide? - After installed the IntellJ, We would like to import the project in the subversion like this link http://sourceforge.net/p/rusefi/code/HEAD/tree/trunk/ - Imported the source project... below. http://i.imgur.com/gi1MZIX.png - Ignore Externals update. http://i.imgur...

What pins have continuity? How many ohms does it read between pins 1-2, then 2-3, then 1-3. That's with 1 on the left and 3 on the right in the above picture. Is this spring loaded? For example, it might be coil 1 = move CW, and coil 2 = move CCW, then no signal means stay still. Also do you have a...

idle speed control for mitsubishi have 6 pin 2 coil Can be used with rusefi? I do not know how to use it. Part Number: MD628054 and MD614568 http://www.lancerregister.com/faq_f22.php http://www.ebay.it/itm/Mitsubishi-FTO-Lancer-Evo-1-2-3-Galant-Idle-Speed-Control-Stepper-Motor-/271098280490 http://w...

There is a problem with TS cranking fuel set max no more than 20ms.

How to open dev console in Eclipse Gui Designer?

Problems can not save config. set_cranking_rpm 400 set_cranking_charge_angle 75 set_cranking_timing_angle 695 set_cranking_fuel_min 20 0 set_cranking_fuel_max 20 90 2014-10-10 14_38: EngineState: fixedModeTiming: 50 2014-10-10 14_38: EngineState: ignitionOffset=0.00000 2014-10-10 14_38: EngineState:...

The problem now is very difficult to start the engine.

original signal ECU


Rusefi signal



yellow = injection1
green= spark1

How to fix ?

russian wrote:http://rusefi.com/forum/viewtopic.php?f=5&t=373&p=11317#p11317

I need to fix right?
rpm 200
set_global_trigger_offset_angle 60

It will make it easier to start engine?

set_global_trigger_offset_angle >> I want to know what it is?

If the shift light function can I use instead mivec .
If possible, I want to have two channels.

4g92 generation 1 non md

ecu pin 109

http://webhost1.inspire.net.nz/~alphaspr/MIVEC/wiring/4g92_ecu_auto.htm

Sure, let's get you http://en.wikipedia.org/wiki/MIVEC Do you know if your engine is an earlier two-profiler system or something continues? http://en.wikipedia.org/wiki/Variable_valve_timing#Continuous_versus_discrete ? You would need to figure out electronic characteristics of the control mechanis...

Now everything works correctly.
I want just the engine mivec control functions only.

This value ok.

How to check set_cranking_fuel_min and set_cranking_fuel_max?
You have command for check?

That's some great data here! The values are not that far off, to make them better you need to make the top temperature setting more accurate (I will now rename "temperature3" to "highest temperature") Let's try C=120.0 R=100.0 as highest temp setting, I think I saw that value in...

http://i.imgur.com/PwPXkde.jpg 100C=200 ohm <<Actual measurements CLT v=0.60219 C=76.68258 R=369.71514 on channel 6 bias=2700.00000 A=0.00271 B=0.00000 C=-0.00000 90C=250 ohm <<Actual measurements CLT v=0.67399 C=74.31204 R=420.66046 on channel 6 bias=2700.00000 A=0.00271 B=0.00000 C=-0.00000 80C=3...

bias resistor can vary, as long as rusEfi has the value of YOUR bias resistor tempinfo should show CLT calculated resistance, please tell us what the value is? Please also disconnect FRK and measure the resistance between GND and CLT wire. Let's make the sure the resistance is calculated correctly....

https://www.diyautotune.com/diypnp/apps/n52/usdm-mitsu-galant-9192-4g63-mt.html

Sensor Calibration
I have to solve the bias resistor?

How much is a default now for set_cranking_fuel_min?

float getCoolantTemperature(void) { float temperature = getTemperatureC(&engineConfiguration2->clt); if (!isValidCoolantTemperature(temperature)) { warning(OBD_PCM_Processor_Fault, "unrealistic CLT %f", temperature); return LIMPING_MODE_CLT_TEMPERATURE; } return temperature; } void se...

I use wide-band sensor. Did you manage to feed the WBO signal info rusEfi? Do you know the parameters of the analog WBO output? I do not remember if we have covered this. I am not 1000% sure but it looks like you are running the with rusEfi? Congratulations on being the first rusEfi installation in...

russian wrote:Are you using some wide-band O2 sensor or a narrow-band O2?

I use wide-band sensor.

[video]http://youtu.be/SJ8Qv_kLMRs[/video] เราไม่ได้ยินเสียงเครื่องยนต์? เป็นเครื่องยนต์รุ่นนี้ควบคุมโดย rusefi? กรุณาชี้แจงฉันอยากรู้จริงๆสิ่งที่เกิดขึ้นและถ้าคุณมีรถ # 6? I was test the FRK and rusEFI r.4560 with Tuning Studio on Mitsubishi 4G63. When the Ignition table = 0 it should be display v...

russian wrote:Please connect

with

Today I tested





And the clip video below...

[video][/video]

Thanks,
Mr.X

I have just renamed "Advance0" gauge to "Input Adv #1" since it's the advance of the INPUT pin, not the spark advance as controlled by the firmware. Which wire did you connect with which in order to feed spark signal into rusEfi input? I will double-check the whole thing once I ...

Why advence0 in devconsole to show the value 0 at all times? http://i.imgur.com/VROrUCn.jpg I just want to set ingnition degree and the values ​​that change only. http://i.imgur.com/x8iNTXr.png 2014-09-08 22_40: PortHolder: Sending [sec!11!triggerinfo] 2014-09-08 22_40: EngineState: confirmation_tri...