rusefi.com

параметры термисторов теперь применяются на лету - https://sourceforge.net/p/rusefi/tickets/201/

Usability: CLT and IAT curve parameters are now applied without reboot. https://sourceforge.net/p/rusefi/tickets/201/

Welcome! Would the CAN sniffer work in between the ecu and the dash/bcm to help reverse engineer the communications? I would like to keep the stock gauges. Can the unused injector drivers be used to control the transmission? there is a custom firmware for sniffing only - http://rusefi.com/wiki/index...

russian wrote:Starting to place an order for frankenso_rev00.40 ETA mid-June.

Order placed! Looks like there would be a ~$40 bump in the price. Time to test http://rusefi.com/forum/viewtopic.php?f=4&t=577 this would shave about $20 off the price.

Usability: it is now possible to change injection & ignition pins assignment on the fly. This should make things easier while setting everything up.

todo: make most/all pin assignments configurable on the fly. https://sourceforge.net/p/rusefi/tickets/198/

Starting to place an order for frankenso_rev00.40 ETA mid-June.

https://svn.code.sf.net/p/rusefi/code/trunk/hardware/mini48-stm32/known_issues.txt

[video][/video]

Number-One wrote:Can´t find information about this sensor. It´s original from Honda cbf and cbr 125.
Keihin brand.

measure voltage at open air - check your weather forecast, that would be one point. do you have anything to make & measure vacuum?

Do you have a picture and part number for your map sensor? The best way to calibrate is to find the specs online

what is this pretty liquid flux this guy is using in the video above?

That $5 box above is a bit too small, here's the winner in my view: MEC85-561 MEC85-561 ECU was used on 2005 Nissan Sentra, there is a lot of these on eBay, they work work with that popular 121 pin connector and these are waterproof. I've got one of these already and the board size is pretty much th...

I wonder how much smaller would this module be if we use TSSOP package op-amp and 0603 resistors?

Finally placed an order for this board!

Need someone in the US who would volunteer to solder the chip for me, I am hopeless with this small pitch

puff wrote:как это во время езды? одним и тем же датчиком измерять давление в коллекторе и атмосферное?

Есть мнение, что в некоторых состояниях двигателя да, у нас атмосферное давление. См. http://www.thirdgen.org/forums/diy-prom/256564-baro-da-calculations-730-a.html

meXanicus wrote:Для барокоррекции нужен отдельный дад, или используется тот же что и в коллекторе, только до пуска мотора?

пока только внешний, скоро будет замер ДАД до старта, а потом и замер ДАД во время езды

Number-One wrote:Great. Can i order one?

http://www.ebay.com/itm/261815066732

I think I'm going to add this to Frankenso R0.4 Does not it look like OEM manage to read baro from the MAP sensor uder certain load? I do not think that baro is such a pressing issue that we would need to add a dedicated sensor. I guess eventually we would want waterproof case and would not we have...

Number-One wrote: 2015-05-11 22_00: EngineState: tps min 193/max 43 v=0.66 @PA3
2015-05-11 22_00: EngineState: current 10bit=117 value=0.00 rate=0.00

I think I see the problem on my side, please stay tuned.

rus084 wrote:i have problems with setup FSIO

please elaborate. have you seen http://rusefi.com/wiki/index.php?title=Manual:Flexible_Logic ?

kb1gtt wrote:http://rusefi.com/forum/download/file.php?id=1268

Good stuff! I have the same sensors on my Neon, but less data points. I've just updated your config with these numbers.

can you please do
tpsinfo
in rsuEfi console a couple of times at different adc values and post the output?

А можно написать название ключа буквами, чтоб например поиск по сайту находил этот топик?

one gauge is showing TPS voltage (tps adc, 0-1023)
another gauge shows TPS position (0-100%)

what are your TPS calibration values?

оффтопик: чуваки, ну что вы делалете B или URL? вон же правильная кнопка - tag! и будет @

http://www.stealth316.com/2-isc-iac.htm ISC for mitsubishi all model You are an example for the use on Rusefi ? I believe this one would work with rusEfi as long as you have the A4988 module - you would connect only four wires and simply leave two wires unconnected. I do not have a stepped like tha...

Tambralinga wrote:Input speed sensor pull-up or pull-down?

pull-up and op-amp in case of my hall sensor, yours could be different,

My VSS hall sensor uses same exact circuit as your your shaft position hall sensor: pull-up, then op-amp, then op-amp output is traced to VSS rusEfi pin which is PA8 in my case.

I think this should be controlled via FSIO, not custom code.

FSIO would allow you define a formula which would translate your RPM into duty cycle, that's exactly what FSIO was designed for.

не успеваю сейчас в этом сильно покопаться так что ответа нет, а вопросы верные.