rusefi.com

Добавил в http://rusefi.com/forum/viewtopic.php?f=8&t=457 ссылку на список артикулов и ссылку на инструкцию в вики

12 каналов low side - VNS14NV04
CAN шина - SN65HVD230

I guess for a detailed 'report' can you provide two sets of data:
both pot resistances
voltages in a couple of junctions of both channels?

Yes I did see the schematic http://i.imgur.com/cnEZuAX.png

I am poking Jared because... See my signature.

voltage on PA3 is affected by changes in BOTH IAT pot and TPS pots?

Can you track it to the op-amp inputs and see if channel 6 input at the op-amp is affected by both pots?

So actually http://i.imgur.com/UT4GGzX.png http://i.imgur.com/yVKyepd.png Please download fresh firmware, it has the fixed default configuration: engineConfiguration->tpsAdcChannel = 4; // input channel 5 is PA4, that's ADC4 engineConfiguration->cltAdcChannel = 2; // input channel 7 is PA2, that's A...

Yes, please remove two pull-downs and one pull-up on your CLT IAT TPS channels

My mistake - I have wrongfully assumed that Frankenstein analog board pinout is the same as analog input v 0.2 you are using. Let me change the channel mapping in the firmware real quick.

PS: once you take these three off, can you please check if voltage actually changes on inputs when you spin the pots?

You should remove TPS pull-up and CLT and IAT pull-downs
Here is how it should be:

Q: Is there a way to print debug messages from interrupt handlers? A: Sure there is! Since rusEfi is just a bunch of interrupt handlers, obviously we need a way to print debug messages from any context. This is implemented in datalogging.c * The idea is that each interrupt handler would have it's ow...

Q: Looks like there are some changes to ChibiOS source code? A: Yes, there are a couple of changes. These are all to improve debugging - __FILE__ & __LINE__ is added into chDbgPanic macros, current thread name added into stack overflow panic message. You can compile rusEfi with unchanged ChibiOS...

Please try troubleshooting it using this table - it should tell you which input is routed to each discovery pin.
*a wrong table was here*

The voltage on the pins should change if inputs change. What are your pull-up and pull-down resistors on these three channels we are playing with now?

That's for the generic, non-rusEfi public - so I guess it would the easier to use the off-the-shelf board for them.

Looks like OBD-II pinout is standard - it's just a question if the pins would be there or not. Say the 2003 Cooper - it has CAN, but it's not on the OBD-II connector.

That's a HOWTO for a Nissan forum, in case anyone would find it interesting - http://rusefi.com/wiki/index.php?title=Manual:Hardware:CAN_sniffer

BTW here is the now-yellow race car build log: http://www.fordfestiva.com/forums/showthread.php?40332-460-festiva-to-run-in-Lemons

And here is our bragging thread - http://forums.24hoursoflemons.com/viewtopic.php?pid=235215

Gimp hint: if the extension was wrong I assume you were trying 'Save' or 'Save as...'. That's a kind in GIMP: you need to use 'overwrite' or 'export' to get a common file format. I've adjusted "Ford 1995 inline 6" configuration for CLT, IAT and TPS. FYI here is the code: setThermistorConfi...

Perfect, that's exactly what I was looking for.

The plywood... That's a step forward from my pegboard

A picture paints a thousand words.

I am back from the soldering duty, there will be some firmware support for this later today - that's now #1 on my list.

Wow

я пока не сильно понимаю зачем менять последовательность структуры . Дима, ты единсвенный кто в теме изменения последовательности в мега-структуре engine_configuration_s Поля нужно переставить местами, чтобы разбить мега-кашу в этой структуре на несколько структур помельче - см. как там уже сделано...

This would also be a lot of manual packaging-labeling on my side, that would be CRAZY inefficient.

Уффф, напаялся на год вперёд.
#2 & #3

Soldering chimp mode off.
#2 & #3

They ask fro 22K, not 2.2K

; Ford ECT
;
; ***** CAUTION - NON STD BIAS RESISTOR REQUIRED *****
; File generated for use with 22000 ohm resistor at R7

I am an opposite of an expert here, my paranoia tells me that not referencing existing designs looks safer

In short terms, it's totally f-up. For firmware, please re-ask the Q if you want to at http://rusefi.com/forum/viewtopic.php?f=13&t=324 But there is also http://rusefi.com/forum/viewtopic.php?f=13&t=325 Hardware I have even less understanding, I am simply paranoid and the less pics of existi...

Baby steps. We've got a cute baby, let's teach it everything together. I would need your help & input. Gotcha. Most of the cars I've got stock ECU location is somewhere closer to the driver, so the tubing idea just seems kind of wrong :) Power supply: http://rusefi.com/wiki/index.php?title=Manua...

TPS channel 5 CLT channel 6 IAT channel 7 MAP channel 8 As you remember, as of today there is only one engine running. We only have what we have needed so far, there will be Frankenstein 0.2, 0.3, 0.4 and probably 0.5 at some point. Hopefully there will be. Anyway. I was always curious, why would MS...

Not sure what it is. Probably some hint of http://rusefi.com/forum/viewtopic.php?f=4&t=381 ? That's still WIP

For now you would need stm32f4discovery - this name is also the part number.