rusefi.com

Nearly done with first stage of polishing... http://tapatalk.imageshack.com/v2/14/09/10/484f4a4c4cd45c5cb15e03d9803475c5.jpg http://tapatalk.imageshack.com/v2/14/09/10/0a6feba82aecaba429e11fda5e08319b.jpg http://tapatalk.imageshack.com/v2/14/09/10/99b6ffa202d854f3613e68658636fe19.jpg Sent from my iP...

kb1gtt wrote:At an ambient of 44C and high RPM, this would be in the realm of unknown. If worst comes to worst we can add a fan to the heat sink.

I was planing that to preempt and add reliability in Australian conditions these things will probably be needed anyway...

So I originally planned for a 75C, and this lower temperature chip would drop that to 35C, so I would expect you will either need a heat sink, or you'll need to draw significantly less than .125A. Just lerking here and am curious if you think this will affect me KB? Summer can easy hit 44C and then...

Melton here mate....

Poseidon wrote:

Kartman wrote:How far am I from Poseidon? No idea. I'm bayside.

Bayside "????state????"

Sandringham????

Kartman wrote:How far am I from Poseidon? No idea. I'm bayside.

Bayside "????state????"

Stand-by for the "UnBoxing" dundundu (music plays........)

Having soldered a couple of these I will throw in a syringe of soldering paste into your box, I want you to success not kill yourself with a soldering iron :) Thank you heaps!!!! Have never used soldering paste... I have done extensive soldering just a bit shaky these days from medications and pain...

I am not a professional shipper yet :( Conversion roughly on the $90 all good no problem my bad estimate lol, don't worry mate not on you just shipping is expensive I know I've been dealing with it for 10 years and well sometimes my mum doesn't tell me but I'm sure when she sends chrissy presents a...

I might get them shipped to my mum in Nevada and pretty sure she can get them shipped here for less than $90

Not all items in your cart are currently shippable to your selected country. Enter your email address if you'd like to be notified when we are able to ship them to you.

russian wrote: The list looks right - with Frankenso kit + discovery you should be all set. LCD and 64 pin connector both optional.

Thank you Mate I'm ordering now yeeeeeeeaaaaaaahhhhhh!!!!!

Selling Locally.......

Once I have walked through the assembly process and have this car running I'd like to open a dialogue about becoming a distributor here in Australia because if I get the results I think and can see. This is going to be very big here!!!!!!!

You would not need 5v power supply because the kit contains all the parts you need to make a power supply on the board. You would need about a 100 resistors, something like http://www.ebay.com/itm/2300pcs-SMD-0805-0-10M-50value-Resistor-2-2pf-1uf-40value-Capacitor-Kit-Set-/110941312626 would cover ...

Yes- it's firing injectors in two batches of three injectors. Thanks Mate, I was taken aback when I had seen this as diesel only injects the cylinder that is at TDC compression stroke with timing of course. Would this not be less efficent than injecting at the time of intake valve opening and then ...

Ordering Parts................ Can anyone please confirm that if I order the following parts I'll be able to have the Frankenso 0.1 Full Bundle and only need a couple capacitors, resistors, 5v pwr supply and vehicle interface plug.... Oh yeah solder and my solder iron I prepared earlier..... If so ...

Question........................

I know I come from diesel background but is it correct that three injectors are firing?

Testing.............................. The pictures are as engine and transmission sits currently, I can't power up anything until I have it back in the car as the wiring has been unshielded and dash + interior completely stripped. I've ordered the new Exedy clutch today and need to get the flywheel...

That's the sticky wicket!!!! Looking at only the harmonic balancer, plug & dust cover to confirm. The rest of the engine would seem very very close to exactly the same which matches with my information regarding production for exactly the same models. The DFI module is exactly the same and has ...

kb1gtt wrote:Do you have a schematic for that sensor? Is that 2 sensors with 4 wires? That could be two VR's or 2 hall sensors. Do you know if 12V and GND go to this sensor?

Hey KD it just so happens here's one I prepared earlier...............................

Are we talking VR or hall? I'm afraid I don't actually know.... Very good question. I'm going to get part numbers today but as of now I don't have them it's already installed and the old one is kinda painted over LOL.... I'll post pics and you'll probably beat me to it but need spec's for it anyway...

Cheers KB No I won't be using OEM.... I plan on something a little more flash (flux capacitor style from back to the future) all good. If you recommend it in the states it's needed here for sure then as we get weeks in the 40's sometimes (like 105-110F) also why she will be running an inter-cooler ...

Can you mount a starter & spin the engine while on this stand, if it's still on the stand? Can you take a picture/provide part numbers for crank and/or cam sensor on this engine? Valid Questions.... I will be installing it in the vehicle before I have the first drop of solder on the board unfor...

Cheers Mate!!! I'll just confirm my order list shortly ie when I wake up as it's 1am and I'll just do a touch of reading before a get some rack. P.S. I have now ported my adventure over to your car & your engine page of the forum thank you for such a great initiation to rusEFI!!! Kind Regards Jay

Project Engine

L27 3800 Series 1 Holden/Buick Motor

Summary G'Day to everyone!!! My name is Jay. I have lived in Australia for 10 years as an American Expat. I rebuilt my first motor when I was 7. My dad gave me a Honda 250 three wheeler (back in the early '80s) and the manual and said "the tools are in the garage, put them back. If you have a ...

1993 Holden Commodore Ute VR

GM proprietary ALDL (OBD1.5) ECU to Frankenstein Conversion...... Let the adventure begin.....................................

https://www.tindie.com/products/russian/frankenso-diy-parts-kit/ is probably a bit nicer because power supply, LCD and connector on the same board - but the downside is shipping cost. You might want to get https://www.tindie.com/products/russian/stm32f4discovery-brain-board/ which you would need an...