Hardware inside and outside of the ECU
Ignition drivers
Replies: 8
by
Simon@FutureProof »
Sun Aug 26, 2018 1:55 pm
What is everyone using for ignition drivers with these boards?
The common goto Bosch BIP373 IGBT seems to be no longer available at least in the UK...
8 Replies
7878 Views
Last post by Abricos
Sat Sep 01, 2018 12:08 am
[help needed] What's up with all the mini-USB ports
Replies: 5
by
stefanst »
Tue Aug 21, 2018 1:37 am
My latest Frankenso board has three spots for mini-USB ports. Two of them are populated with a connector.
One is labeled TTL and when I plug this...
5 Replies
4639 Views
Last post by stefanst
Wed Aug 22, 2018 1:27 am
[help needed] IDLE not working
Replies: 13
by
gptech2444 »
Fri Jun 15, 2018 1:44 am
Hi,
I have no output for the idle control. I have a BAC that standard on Mercedes. I wired it 12v one side and the other to INJ-01(PE6) and there is...
13 Replies
10833 Views
Last post by Simon@FutureProof
Sun Jul 29, 2018 4:11 pm
Main Board PROG USB connector
Replies: 4
by
stefanst »
Mon Jul 16, 2018 2:26 pm
My brain seems to be on vacation. We have a PROG USB connector on the main board. I'm pretty sure I used it on my previous rusefi. However, I can't...
4 Replies
3506 Views
Last post by stefanst
Mon Jul 16, 2018 2:57 pm
[help needed] Something strange with my knock module
Replies: 5
by
Lyonz »
Wed May 30, 2018 6:01 pm
New topic from:
let's move into some knock-related topic or start a new one?
What does hipinfo command say in rusefi console?
To answer your...
5 Replies
4246 Views
Last post by AndreyB
Fri Jun 01, 2018 11:35 am
[SOLVED]Fatal error: angle NaN ...
Replies: 6
by
hossein »
Thu May 24, 2018 1:23 pm
During I was testing fuel table config on my engine, and after 10 minutes, The ecu showed critical signs.
No trigger and so no ignition &| injection...
6 Replies
5685 Views
Last post by kb1gtt
Sat May 26, 2018 9:12 am
60 pin ECU connector
Replies: 5
by
Joeldc510 »
Wed Apr 25, 2018 11:06 pm
I'm looking for a specific 60 pin ecu connector to try implementing rusefi in a plug and play application. Its found in the aem infinity but looking...
5 Replies
4938 Views
Last post by AndreyB
Thu Apr 26, 2018 4:38 am
[help needed] ADC Alt CAM, Alt CRANK RC filter
Replies: 3
by
maximus64 »
Wed Apr 11, 2018 5:01 pm
On Frankenso schematic, ADC section for ALT CAM and ALT CRANK have a label that said low pass filter knee at 100kHz typical . Is the 10K before the...
3 Replies
3575 Views
Last post by RadMx5
Sat Apr 14, 2018 8:17 am
Alternator field control circuit
Replies: 64
by
AndreyB »
Sat Dec 06, 2014 8:16 pm
See for software side of alternator control
How do you like this
The charging lamp will come on if either the inlet air temperature, coolant...
64 Replies
49510 Views
Last post by gptech2444
Wed Apr 11, 2018 10:47 pm
9 Replies
12121 Views
Last post by pobedyst
Tue Apr 10, 2018 8:51 am
2 Replies
2689 Views
Last post by AndreyB
Sun Apr 08, 2018 12:34 pm
[help needed] frankenso v0.5 5V rail problem
Replies: 24
by
maximus64 »
Fri Feb 16, 2018 6:20 pm
I just got my frankenso kit from tindie and assembled the 5V power rail section. I load tested the power supply with 13V input and it can only handle...
24 Replies
15493 Views
Last post by kb1gtt
Mon Mar 26, 2018 5:08 pm
[help needed] Stm32f4 integration
Replies: 3
by
Ilcapo »
Sun Mar 04, 2018 5:29 pm
Hello rusefi.com forum,
Has anyone integrated stm32 and all the required components into the frankenso board? If so do you have a list of all the...
3 Replies
3523 Views
Last post by kb1gtt
Sun Mar 04, 2018 9:31 pm
pumping 3.3V to 3V rail
Replies: 6
by
puff »
Sun Feb 04, 2018 8:53 am
It's not a secret that our 3.3V rail is actually not.
For my canbus-related exercises, the lack of those ~0.3V-0.4V was critical. So I decided add a...
6 Replies
5046 Views
Last post by puff
Fri Mar 02, 2018 2:20 pm
minEFI
Replies: 26
by
rus084 »
Sun Jul 26, 2015 12:04 pm
i will make small ecu board .
i deleted all no needed for me from frankenso and get something about this:
1.png
NOW:
2.png
im learning KIKAD...
26 Replies
27394 Views
Last post by rus084
Thu Mar 01, 2018 6:47 am
lcd + pcf8574 I2C adaptor
Replies: 3
by
mazdee »
Wed Jan 31, 2018 8:51 pm
hi there.
i am building my own customised setup and can now happily connect to cheap ebay stm32f407 diy more board.
I have found an I2C 20x4 lcd...
3 Replies
3116 Views
Last post by mazdee
Thu Feb 01, 2018 7:28 am
Trigger issue
Replies: 5
by
hossein »
Sun Aug 27, 2017 3:59 am
This is a part of topic of past .... so.
After some successful experience, my ecu board has some little issues.
The trigger source -crank sensor -...
5 Replies
5241 Views
Last post by kb1gtt
Sun Jan 28, 2018 5:56 pm
[help needed] Coil on plug question
Replies: 31
by
V8Volvo245 »
Sun Dec 31, 2017 7:35 pm
I've just noticed that the coils on my engine are only two wire i.e. they don't have built in ignitors. Can I still use Rusefi or do I have to go...
31 Replies
19423 Views
Last post by puff
Sat Jan 06, 2018 10:41 pm
SLC oem from 14point7
Replies: 12
by
AndreyB »
Tue Dec 16, 2014 4:35 pm
SLC OEM is a low-cost, miniature Wideband O2 Controller suitable for integration into your own products/projects. It is a complete Wideband O2...
12 Replies
16230 Views
Last post by kb1gtt
Mon Jan 01, 2018 10:37 am
6 Replies
6044 Views
Last post by kb1gtt
Fri Dec 22, 2017 4:54 pm
7 Replies
5505 Views
Last post by kb1gtt
Tue Dec 19, 2017 11:10 pm
7 Replies
5584 Views
Last post by V8Volvo245
Sun Dec 17, 2017 9:28 am
[help needed] VNS14NV04 obsoleted --- Ooops
Replies: 14
by
Roo-Barb »
Sun Nov 08, 2015 9:50 am
Hi
I was putting my frankenso together and accidentally blew away a few of the VNS14NV04 chips with the smd heat gun, and I searched the room and...
14 Replies
10647 Views
Last post by dreamhazard
Thu Dec 14, 2017 6:42 pm
Protection against back EMF
Replies: 1
by
danhuang »
Tue Nov 07, 2017 6:16 am
I don't know if this is off topic, if so, delete it, thanks.And sorry to everyone
Recently, I am trying to build an ignition cut module with an...
1 Replies
3527 Views
Last post by kb1gtt
Wed Nov 08, 2017 7:35 pm
track telemetry - data radio
Replies: 73
by
AndreyB »
Mon Apr 24, 2017 1:38 pm
I am afraid of radio, my perception is that's dark voodoo magic and it simply would not work unless I have a Ms degree in physics.
I am sure that...
73 Replies
44617 Views
Last post by Abricos
Fri Oct 20, 2017 12:39 am
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum