2003 VVT turbo miata dev mule

Your chance to introduce yourself and your vehicle
Post Reply
mediocre machinist
Posts: 2
Joined: Thu May 13, 2021 1:33 am
Location: BC, Canada
Github Username: LJspice
Slack: miata_na6_nb2

2003 VVT turbo miata dev mule

Post by mediocre machinist »

Good evening. Or morning, I don't judge

The good news:
After an intense global headhunting process, the rusEFI devs have found a willing test subject for the NB2 plug and play ECU setup.

The bad news:
It's me

The car:
- 2003 Miata, it gots the VVT
- Kraken low mount & 3" exhaust
- Garrett GTX2867R gen 2, 0.64 A/R
- ID1050x injectors
- LSU 4.9 wideband
- Link G4X fury ECU, with my own plug'n'play adapter. Custom yo
image.png
image.png (2.26 MiB) Viewed 3980 times
image.png
image.png (2.26 MiB) Viewed 3980 times
The plan:
- Install E-throttle
- Wire/plumb in flex fuel sensor
- Swap between ECU's, collect data and feedback where needed to support development. When development is complete, my buddy will need an ECU. The outcomes of testing will determine which one he gets to buy :)

The author:
- Mediocre machinist, it's a hobby thing
- Mediocre welder, you get the idea
- R&D eng day job
- Mech eng by schooling
- Former FSAE nerd

I haven't touched anything beyond 8-bit microcontrollers, please be gentle
User avatar
AndreyB
Site Admin
Posts: 14292
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Github Username: rusefillc
Slack: Andrey B

Re: 2003 VVT turbo miata dev mule

Post by AndreyB »

Welcome to https://github.com/rusefi/rusefi/wiki/Hellen72

Your board has already made to Jamaica, NY! Please warm your mini USB cable.
Very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions

Always looking for C/C++/Java/PHP developers! Please help us see https://rusefi.com/s/howtocontribute
stefanst
contributor
contributor
Posts: 703
Joined: Wed Feb 17, 2016 12:24 am
Location: USA 08530

Re: 2003 VVT turbo miata dev mule

Post by stefanst »

Welcome to the forum. Which ECU are you currently running? Any dyno runs from the car? (A selfish question- I have a Kraken high mount with 2560R ready to go, once my NB1 with NB2 engine is rescued from its' current state of complete disassembly)
BeerMoneyMotorsports
Posts: 151
Joined: Thu Jan 14, 2021 10:16 pm

Re: 2003 VVT turbo miata dev mule

Post by BeerMoneyMotorsports »

Just so you know im the fastest miata here and dont attempt to change that or else!

In all seriousness, sub 300whp im guessing since stock bottom end?
stefanst
contributor
contributor
Posts: 703
Joined: Wed Feb 17, 2016 12:24 am
Location: USA 08530

Re: 2003 VVT turbo miata dev mule

Post by stefanst »

My stock NB1 bottom threw some rods and side-vented the block at around 14psi. at 12 psi it showed around 230hp on Virtual Dyno at 5500rpm or so. 10 psi was 205 (I think) on a Mustang. But that was in 2012 and I can't remember that far back. There seem to be a few stock bottom ends that can handle around 300hp, but you have to bring the boost in late and increase it after 5000rpm when the torque curve falls off, so you keep making more power, but keeping the torque well below 250ftlbs. I think 240ftlbs at 6700 is approx 300hp and *should* be safe-ish on a stock bottom end.
BeerMoneyMotorsports
Posts: 151
Joined: Thu Jan 14, 2021 10:16 pm

Re: 2003 VVT turbo miata dev mule

Post by BeerMoneyMotorsports »

I e left that all behind for the built motor holy land
mediocre machinist
Posts: 2
Joined: Thu May 13, 2021 1:33 am
Location: BC, Canada
Github Username: LJspice
Slack: miata_na6_nb2

Re: 2003 VVT turbo miata dev mule

Post by mediocre machinist »

Been a while since I checked this...

Still stock bottom end, planning to build it up over winter. No dyno runs yet, only road tuning. Just running 5psi spring pressure for now, but it boost creeps to 10 near redline in 4th...need to port that out

It is on a Link G4X fury ECU right now
Post Reply