Vitara 1.6 8v

Your chance to introduce yourself and your vehicle
Post Reply
pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Vitara 1.6 8v

Post by pkagiantas »

So here i am :) just got a vitara 1.6 8v TBI ( fitted with lpg too ! ) and 3 days in my possession it i already put it on the dyno

made a whopping 50 wheel hp and 89 NM wheel torque :lol: :lol:
here is a video of the dyno https://fb.watch/eUYox4VTaP/

and the dyno sheet Image


some days later i it crossed my mind to check the base timing and it was at least 5 degrees retarded :roll:


i was wondering if someone has run one with RusEfi yet
i have some proteus units here sitting around 8-)
is the dissy trigger patter supported ?

i will take the distributor apart soon just need to find some spare time

the scope of the project is on the photo :P or to put a 2liter engine on it

Image
User avatar
AndreyB
Site Admin
Posts: 14292
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Github Username: rusefillc
Slack: Andrey B

Re: Vitara 1.6 8v

Post by AndreyB »

pkagiantas wrote:
Sun Aug 14, 2022 6:05 pm
is the dissy trigger patter supported ?
What trigger pattern? Need more info :)
Very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions

Always looking for C/C++/Java/PHP developers! Please help us see https://rusefi.com/s/howtocontribute
ELMEPRO
Posts: 24
Joined: Thu May 12, 2022 7:24 pm
Location: Latvia

Re: Vitara 1.6 8v

Post by ELMEPRO »

usually before tuning car we check ignition with timing and check if trigger wheel decoding correctly?! :D
pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Re: Vitara 1.6 8v

Post by pkagiantas »

ELMEPRO wrote:
Mon Aug 15, 2022 12:13 pm
usually before tuning car we check ignition with timing and check if trigger wheel decoding correctly?! :D
Who tuned what ? ;)
all i did is throw the car on the Dyno ... plus i tune cars for living so dont worry about it all i asked if ithas been done allready

AndreyB wrote:
Sun Aug 14, 2022 10:53 pm
pkagiantas wrote:
Sun Aug 14, 2022 6:05 pm
is the dissy trigger patter supported ?
What trigger pattern? Need more info :)
I haven't took the dizzy apart yet will try to take some photos and a scope on it soon
pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Re: Vitara 1.6 8v

Post by pkagiantas »

AndreyB wrote:
Sun Aug 14, 2022 10:53 pm
pkagiantas wrote:
Sun Aug 14, 2022 6:05 pm
is the dissy trigger patter supported ?
What trigger pattern? Need more info :)
from what i can understand its an even 4 pulse trigger probably a 5v hall sensor
looks easy to modify and put a 24-1 in and run it as a missing tooth cam speed if this one is not supported

all the wires i scoped tho i couldt get a clean signal maybe my probes are not the best and i might actualy got the tacho signal

Image

video here

Image
pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Re: Vitara 1.6 8v

Post by pkagiantas »

also any easy way to drive the injector ?

its a Low z type 8ohms as autodata says
User avatar
MHTSOS
Posts: 74
Joined: Sun Jun 02, 2019 6:46 pm
Github Username: MHTSOSVOODOO
Slack: Dimitri C

Re: Vitara 1.6 8v

Post by MHTSOS »

Easiest way is adding a series resistor.

Στάλθηκε από το VOG-L29 μου χρησιμοποιώντας Tapatalk

pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Re: Vitara 1.6 8v

Post by pkagiantas »

i was under the impression that it needs a peak and hold driver
User avatar
MHTSOS
Posts: 74
Joined: Sun Jun 02, 2019 6:46 pm
Github Username: MHTSOSVOODOO
Slack: Dimitri C

Re: Vitara 1.6 8v

Post by MHTSOS »

Ideally you can make a peak n' hold driver with LM1949 but it can also work with a series resistor to bring the total resistance around 12 to 14 ohms. In that case you will have to calculate the injector dead times from scratch. Best solution would be to install a high-z injector that fits in this manifold. That way you will have reliable data about dead times and flow.
If you eventually install that turbo the stock injector will be too small anyways.

Στάλθηκε από το VOG-L29 μου χρησιμοποιώντας Tapatalk

pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Re: Vitara 1.6 8v

Post by pkagiantas »

cant install a new injector unfortunately its a single point throttle body injector


the idea is to run it as is just to see that everything works
and then fit a saxo fuel rail that seems like it fits and convert it to port injection and slap a turbo on it :D
pkagiantas
Posts: 18
Joined: Tue Feb 15, 2022 5:37 pm
Location: Greece
Github Username: pkagiantas

Re: Vitara 1.6 8v

Post by pkagiantas »

setting the trigger type to Mazda SOCH 4
reads rpm on cranking with out sync loss :mrgreen:

i havet started the car yet still need to modify the intake to fit the injector rail and make a turbo manifold for it
Post Reply