Page 4 of 5

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 12:21 am
by Abricos
russian wrote:
Sun Jul 07, 2019 12:14 am
I am trying to help here. My question is if configuration got corrupted and I am looking for real latest logs and real latest tune. You are free to help me help you or not help me help you :)
real latest logs is updated Sun Jul 07, 2019 12:05 am

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 12:32 am
by AndreyB
Abricos wrote:
Sun Jul 07, 2019 12:05 am
the only changes that I was doing I changed between injector simultaneously or sequential ...
This is supposed to work funny since you do not have cam sensor but it's supposed to work. Do you want to try un-doing sequential back to simultaneous?

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 12:37 am
by AndreyB
You have cranking coolant multiplier set to zero - this multiples your fuel by zero and you get zero fuel.

You have cranking TPS multiplier set to zero - this multiples your fuel by zero and you get zero fuel.

Please set both curves to "1" if you do not want to use those. Please set to something else if you want your cranking to depend on your CLT.

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 12:37 am
by Abricos
russian wrote:
Sun Jul 07, 2019 12:32 am
Abricos wrote:
Sun Jul 07, 2019 12:05 am
the only changes that I was doing I changed between injector simultaneously or sequential ...
This is supposed to work funny since you do not have cam sensor but it's supposed to work. Do you want to try un-doing sequential back to simultaneous?
I will check again simultaneous !!!

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 12:46 am
by AndreyB
russian wrote:
Sun Jul 07, 2019 12:37 am
You have cranking coolant multiplier set to zero - this multiples your fuel by zero and you get zero fuel.

You have cranking TPS multiplier set to zero - this multiples your fuel by zero and you get zero fuel.

Please set both curves to "1" if you do not want to use those. Please set to something else if you want your cranking to depend on your CLT.
There is now a warning code for this case :)

https://github.com/rusefi/rusefi/commit/1fce0201a55c45f8333883cc95589c701d5723d5

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 1:06 am
by Abricos
YES
that was the problem
I had a zero there
I changed to one (see photo below )
it started working :mrgreen:
New Bitmap Image (12).bmp
New Bitmap Image (12).bmp (3 MiB) Viewed 38027 times
New Bitmap Image (2).bmp
New Bitmap Image (2).bmp (3 MiB) Viewed 38027 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 2:51 am
by Abricos
to use sequential do i need CAM sensor ?

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sun Jul 07, 2019 3:21 am
by mck1117
Abricos wrote:
Sun Jul 07, 2019 2:51 am
to use sequential do i need CAM sensor ?
You can run sequential without a cam sensor. However, it may inject 360 degrees out of phase. There's a 50/50 chance of it being correct or "wrong". That said, I ran my engine for 5000mi/8000km without a cam sensor and it set to sequential, and I couldn't tell if it started in phase or out of phase.

tl;dr: you can safely set it to sequential

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Thu Jul 11, 2019 12:34 am
by Abricos
idle control ...
i have cable throttle body ...
but inside (throttle body) there is also electric motor ...
so 2 in one ETB and MTB ...
ETB is for idle control and Cruise control ...
what do you think how will it work ??

p.s.do not listen to what I say on the video :mrgreen:


Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Jul 16, 2019 10:16 pm
by Abricos
maybe anyone have extra time to see the date log
and maybe you see what improvements can be made
I am very interested how to tune Injection Phase ???
6.30.2019#2.rar
(1.54 MiB) Downloaded 695 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Jul 23, 2019 12:48 am
by Abricos
date log from drag race
7.20.2019.rar
(2.23 MiB) Downloaded 646 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Jul 30, 2019 11:51 pm
by mck1117
Abricos wrote:
Tue Jul 16, 2019 10:16 pm
I am very interested how to tune Injection Phase ???
For engines like ours, injection phase doesn't really matter much. You will probably get slightly better emissions, cold start, and idle smoothness if you inject against a closed valve so the fuel vaporizes fully by the time the valve opens. I was unable to observe any difference on my car playing with the injection phase. The injection phase table indicates the END of injection, in degrees after top dead center. So -360 means that injection will finish just as the intake valve is opening. Set it to -400 and call it good.

So how do you tune it? You need an engine dyno, an ultra-expensive exhaust gas analyzer, and an unbelievable amount of time.

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Fri Mar 06, 2020 10:28 pm
by Abricos
if you want to use your standard cable pedal ! BUT electronic throttle ...U need first
honda acura accelerator pedal position sensor
part number 37971-RCA-A01
s-l1600.jpg
s-l1600.jpg (86.04 KiB) Viewed 37001 times
honda 2.jpg
honda 2.jpg (66.51 KiB) Viewed 37001 times
Connector 6 pin for Honda Acura Accelerator Pedal Sensor
part number 01020101001347
s-l500.jpg
s-l500.jpg (18.36 KiB) Viewed 37001 times
TPS pinout
honda.jpg
honda.jpg (141.83 KiB) Viewed 37001 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Mon Mar 16, 2020 8:51 pm
by Abricos
Hi
So I added TLE7209-R3 H-brige ...
So I connect 12+ 5+ gnd
I connect Throttle position sensor


So I have questions ...
Where to connect H-brige board signal ?
And where to connect pedal TPS ?
IMG_20200316_164306.jpg
IMG_20200316_164306.jpg (5 MiB) Viewed 35635 times
IMG_20200316_164245.jpg
IMG_20200316_164245.jpg (3.73 MiB) Viewed 35635 times
IMG_20200316_164005.jpg
IMG_20200316_164005.jpg (3.83 MiB) Viewed 35635 times
IMG_20200316_164001.jpg
IMG_20200316_164001.jpg (4.57 MiB) Viewed 35635 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Thu Oct 22, 2020 1:20 am
by Abricos
backfire

if you have version frankenso 0.4 and below and if when you turn ON ignition key the coils fire ( backfire )
you need to add resistors to your TC4427 chips
TC4427 chips location
2015-01-24T16_09_19.482Z-frankenso_0_2_assembled.jpg
2015-01-24T16_09_19.482Z-frankenso_0_2_assembled.jpg (400.5 KiB) Viewed 31233 times
you need to add a resistor between the legs TC4427 chips

leg2 (IN A) to 1K resistor to leg3 (gnd)
leg4 (IN B) to 1K resistor to leg3 (gnd)

as in the picture below
New Bitmap Image (2).bmp
New Bitmap Image (2).bmp (725.47 KiB) Viewed 31233 times
This is how I make
IMG_20201022_171716__02.jpg
IMG_20201022_171716__02.jpg (2.79 MiB) Viewed 31211 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sat Nov 07, 2020 11:44 pm
by Abricos
i tried to enable and configure idle and wastgate valve
but it didn't work
i used pin PA2 TPS (WORK)
pin PA3 Idle Valve Position
pin PA4 Wastegate Position
when I move them with my hands, there is no reaction in TS gauges (Position or Raw value)
any ideas?


2020-11-07_18_20_38_618: EngineState: 1604773237 - unix time
2020-11-07_18_20_38_618: EngineState: Current RTC localtime is: 2020-11-07 18:20:37 w=1
2020-11-07_18_20_44_276: EngineState: WARNING: unexpected MAP value: -1.64
2020-11-07_18_20_54_043: EngineState: confirmation_tempinfo:8
2020-11-07_18_20_54_053: EngineState: Sensor "CLT": Raw value: 2.29 Valid: Yes Converted value 22.69
2020-11-07_18_20_54_053: EngineState: 2.29 volts -> 2288.9 ohms with supply voltage 5.00 and pullup 2700.0.
2020-11-07_18_20_54_053: EngineState: 2288.9 ohms -> valid: Yes. 22.6 deg C
2020-11-07_18_20_54_063: EngineState: Sensor "IAT": Raw value: 2.28 Valid: Yes Converted value 22.87
2020-11-07_18_20_54_083: EngineState: 2.28 volts -> 2274.0 ohms with supply voltage 5.00 and pullup 2700.0.
2020-11-07_18_20_54_083: EngineState: 2274.0 ohms -> valid: Yes. 22.8 deg C
2020-11-07_18_20_54_083: EngineState: RPM sensor: stopped: 1 spinning up: 0 cranking: 0 running: 0 rpm: 0.000000000
2020-11-07_18_20_54_083: EngineState: Sensor "MAP" is not configured.
2020-11-07_18_20_54_093: EngineState: Sensor "MAF" is not configured.
2020-11-07_18_20_54_093: EngineState: Sensor "Oil Pressure" is not configured.
2020-11-07_18_20_54_093: EngineState: Sensor "Fuel Pressure (LP)" is not configured.
2020-11-07_18_20_54_093: EngineState: Sensor "Fuel Pressure (HP)" is not configured.
2020-11-07_18_20_54_093: EngineState: Sensor "Fuel Pressure (injector)" proxied from sensor "Fuel Pressure (LP)"
2020-11-07_18_20_54_103: EngineState: Sensor "TPS 1" is redundant combining "TPS 1 Primary" and "TPS 1 Secondary"
2020-11-07_18_20_54_103: EngineState: Sensor "TPS 1 Primary": Raw value: 4.33 Valid: Yes Converted value 0.69
2020-11-07_18_20_54_103: EngineState: Linear function slope: -27.39 offset: 119.45 min: -10.0 max: 110.0
2020-11-07_18_20_54_103: EngineState: raw value 4.33 converts to 0.69 valid: Yes
2020-11-07_18_20_54_113: EngineState: Sensor "TPS 1 Secondary" is not configured.
2020-11-07_18_20_54_113: EngineState: Sensor "TPS 2" is redundant combining "TPS 2 Primary" and "TPS 2 Secondary"
2020-11-07_18_20_54_113: EngineState: Sensor "TPS 2 Primary" is not configured.
2020-11-07_18_20_54_113: EngineState: Sensor "TPS 2 Secondary" is not configured.
2020-11-07_18_20_54_123: EngineState: Sensor "Acc Pedal" is redundant combining "Acc Pedal Primary" and "Acc Pedal Secondary"
2020-11-07_18_20_54_123: EngineState: Sensor "Acc Pedal Primary" is not configured.
2020-11-07_18_20_54_123: EngineState: Sensor "Acc Pedal Secondary" is not configured.
2020-11-07_18_20_54_123: EngineState: Sensor "Driver Acc Intent" proxied from sensor "TPS 1"
2020-11-07_18_20_54_123: EngineState: Sensor "Aux Temp 1" is not configured.
2020-11-07_18_20_54_123: EngineState: Sensor "Aux Temp 2" is not configured.
2020-11-07_18_20_54_123: EngineState: Sensor "Wastegate Position": Raw value: 2.56 Valid: No Converted value 0.00
2020-11-07_18_20_54_123: EngineState: Linear function slope: -598.80 offset: 107.18 min: -10.0 max: 110.0
2020-11-07_18_20_54_123: EngineState: raw value 2.56 converts to 0.00 valid: No
2020-11-07_18_20_54_123: EngineState: Sensor "Idle Valve Position": Raw value: 5.03 Valid: No Converted value 0.00
2020-11-07_18_20_54_123: EngineState: Linear function slope: -6666.66 offset: 133.33 min: -10.0 max: 110.0
2020-11-07_18_20_54_123: EngineState: raw value 5.03 converts to 0.00 valid: No

2020-11-07_18_20_54_123: EngineState: fan=No @ PE5
2020-11-07_18_20_54_123: EngineState: A/C relay=Yes @ NONE

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Mon Nov 09, 2020 1:10 am
by Abricos
I checked and make sure that my hardware is in working order....


And now I don't know what to do next.
maybe I don't understand how to activate waste gate and idle (DC motor ) to work...

https://rusefi.com/online/view.php?msq=272

TS CurrentTune
11.7.2020.zip
(366.72 KiB) Downloaded 561 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sat Nov 14, 2020 11:16 pm
by AndreyB
Functually everything seems fine with both sensors but usability was not great. I've added defaults and tool tips clarifying that 1 volt means 1000 units.
image.png
image.png (116.6 KiB) Viewed 30816 times
Your settings at https://rusefi.com/online/view.php?msq=272&dialog=wastegateIdlePos were the issue, please start from "min 0 max 5000" which would mean "min 0 volts max 5 volts"

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Dec 08, 2020 9:04 am
by AndreyB

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Jun 01, 2021 12:55 am
by Abricos
maybe someone will look ... in the logs you can see the delay on the gas pedal (any recommendations where to adjust )???

31.05.2021.rar
(889.2 KiB) Downloaded 497 times

logs
https://rusefi.com/online/view.php?log=251

tune
https://rusefi.com/online/view.php?msq=542

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Sat Jun 26, 2021 4:01 am
by AndreyB
Nick can you please post some fresh pictures of your engine bay since it looks NICE!

Also let's see how can I help with https://github.com/rusefi/rusefi/issues/2861

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Jul 13, 2021 1:46 am
by Abricos
the hybrid part of the project is also developing slowly
in the photos electric motors MGR from lexys RX 67 HP
several photos of a suspension with a motor and a video of a battery from a Ford energy 8.8 kilowatts
IMG_20210712_195155.jpg
IMG_20210712_195155.jpg (4.9 MiB) Viewed 27913 times
IMG_20210712_182012.jpg
IMG_20210712_182012.jpg (5.15 MiB) Viewed 27913 times
IMG_20210712_182004.jpg
IMG_20210712_182004.jpg (5.02 MiB) Viewed 27913 times
IMG_20210712_181954.jpg
IMG_20210712_181954.jpg (5.86 MiB) Viewed 27913 times
IMG_20210712_181954.jpg
IMG_20210712_181954.jpg (5.86 MiB) Viewed 27913 times
IMG_20210712_163728.jpg
IMG_20210712_163728.jpg (5.7 MiB) Viewed 27913 times
IMG_20210712_160224.jpg
IMG_20210712_160224.jpg (5.96 MiB) Viewed 27913 times
battery pack Ford energy 8.8 kilowatts



Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Thu Jul 15, 2021 3:23 pm
by dexter_lab
is it going to fit on miata? :)
Nice project by the way

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Wed Jul 28, 2021 1:52 am
by AndreyB
Do you have a drill? Do you have BorgWarner turbo?

https://www.full-race.com/docs/Speed-Sensor-Installation-Instructions.pdf

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Aug 17, 2021 12:47 am
by AndreyB
Something is not right with rusEFI, specific ECU or vehicle in some regard.

TPS drama was noticed at 9:18 of


TPS was replaced. https://github.com/rusefi/rusefi/issues/3166 created

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Aug 17, 2021 12:59 am
by AndreyB
We have the log of highway auto-tune stall https://rusefi.com/online/view.php?log=315
image.png
image.png (190.61 KiB) Viewed 27437 times
I see RPM gradually going down so ECU has not rebooted. I see engine not responding to fuel.

I see break of AFR pattern - normally it looks like AFR was rich on lift off but when it has stalled AFR was reporting lean all the time? Not sure what is the cause what is consequence.

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Aug 17, 2021 1:14 am
by AndreyB
Going back to 455 second of same log we see that small throttle on idle has choked engine. That makes me question acceleration enrichment settings

https://rusefi.com/online/view.php?msq=612&dialog=tpsTpsAccelTbl

I think that below diagonal values should be zero or BELOW zero not positive?
image.png
image.png (74.63 KiB) Viewed 27434 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Tue Aug 17, 2021 2:38 am
by mck1117
First step in diagnosis: let's get the warnings under control.
image.png
image.png (27.04 KiB) Viewed 27428 times
CUSTOM_OBD_LOW_FREQUENCY
CUSTOM_VVT_MODE_NOT_SELECTED
CUSTOM_OBD_SKIPPED_SPARK
CUSTOM_OBD_SKIPPED_FUEL

With so many happening, it's hard to tell which happens when. Please either disable VVT input, or pick a vvt mode so that one goes away (likely the cause of the rapidly increasing warnings).

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Thu Aug 26, 2021 1:23 am
by Abricos
mck1117 wrote:
Tue Aug 17, 2021 2:38 am
First step in diagnosis: let's get the warnings under control.

image.png

CUSTOM_OBD_LOW_FREQUENCY
CUSTOM_VVT_MODE_NOT_SELECTED
CUSTOM_OBD_SKIPPED_SPARK
CUSTOM_OBD_SKIPPED_FUEL

With so many happening, it's hard to tell which happens when. Please either disable VVT input, or pick a vvt mode so that one goes away (likely the cause of the rapidly increasing warnings).
Hello
I don't have VVT
Screenshot_20210825-173258.jpg
Screenshot_20210825-173258.jpg (419.95 KiB) Viewed 27306 times

Re: Моё Чудо ... VW Passat B4 ABA ... #16

Posted: Thu Aug 26, 2021 1:28 am
by mck1117
You have a cam sensor selected. Please set it to none.