[info] STM32F407VET6 Mini Development Board System Board

Hardware inside and outside of the ECU
puff
contributor
contributor
Posts: 2961
Joined: Mon Nov 11, 2013 11:28 am
Location: Moskau

Re: STM32F407VET6 Mini Development Board System Board

Post by puff »

:-) same stuff
PA11 and PA12 - directly to usb cable or to usb-serial adapter?
vcc to PA9 - what's that?
Old Grey
contributor
contributor
Posts: 85
Joined: Thu Apr 07, 2016 10:20 pm
Location: AUS Sydney 2200

Re: STM32F407VET6 Mini Development Board System Board

Post by Old Grey »

I should've known NickZ would've been ahead of the game. :D

Looking at the VG Dev board SCH it says the USB is connected to PA12, PA11, but PA9 to VCC I don't know about. F-ken is PA9 to VBUS, so it must be a thing.

These things would make great baby Fsteins. Like make a shield the same size for 1-2 cyl small engines and bikes, and then another stack shield to add an extra 2-4 cyls for big bikes. Or put it solely on a Fstein - a Frankendevon :D -, and that would give it room to put a straight header system onboard for a direct adaptor PCB connection.

Even though direct programming is confusing to me, I might risk getting one.
Last edited by Old Grey on Mon Jan 20, 2020 1:56 pm, edited 1 time in total.
puff
contributor
contributor
Posts: 2961
Joined: Mon Nov 11, 2013 11:28 am
Location: Moskau

Re: STM32F407VET6 Mini Development Board System Board

Post by puff »

what's f-ken?
2019-12-23 11.04.59.jpg
2019-12-23 11.04.59.jpg (174.53 KiB) Viewed 6993 times
here's mine - looks a bit different?
NickZ
Posts: 56
Joined: Sun Sep 01, 2019 9:44 pm

Re: STM32F407VET6 Mini Development Board System Board

Post by NickZ »

The usb won't work without the PA9 to VCC, I think its to do with the bootloader looking for PA9 being high to enable Native USB through PA11 and PA12, even if you pull the power from PA9 the usb will disappear.

I have successfully run RusEFI on this board on the bench, But it was a stepping stone for my own development version of ECU board.

as far as i can see the Supplied USB socket doesn't do anything.

I used a ST-Link v2 to upload the firmware before being able to use the USB on pins PA11 and PA12.
Old Grey
contributor
contributor
Posts: 85
Joined: Thu Apr 07, 2016 10:20 pm
Location: AUS Sydney 2200

Re: STM32F407VET6 Mini Development Board System Board

Post by Old Grey »

NickZ wrote:
Mon Dec 23, 2019 8:39 am
I used a ST-Link v2 to upload the firmware before being able to use the USB on pins PA11 and PA12.
It's starting to get a bit clearer.
NickZ wrote:
Mon Dec 23, 2019 8:39 am
as far as i can see the Supplied USB socket doesn't do anything.
That's weird. Maybe it's because it doesn't have PA9
NickZ wrote:
Mon Dec 23, 2019 8:39 am
The usb won't work without the PA9 to VCC, I think its to do with the bootloader looking for PA9 being high to enable Native USB through PA11 and PA12, even if you pull the power from PA9 the usb will disappear.
You'd know more about that than me, but I'll try it when the VG DEV gets here.
NickZ wrote:
Mon Dec 23, 2019 8:39 am
I have successfully run RusEFI on this board on the bench, But it was a stepping stone for my own development version of ECU board.
That's enough proof that it's worth looking at.
puff wrote:
Mon Dec 23, 2019 8:05 am
what's f-ken?

here's mine - looks a bit different?
F-ken is my short for Frankenso. :)

My pic has better lighting so might look different, but to me it looks genuine. Same font and broken nub in the top right circle depression.
puff
contributor
contributor
Posts: 2961
Joined: Mon Nov 11, 2013 11:28 am
Location: Moskau

Re: STM32F407VET6 Mini Development Board System Board

Post by puff »

late followup. I just started the recent rusefi image on this board! (used jlink to flash it, had to solder on a 3k pull-up to pa12). I was surprised to see a usb disk with probably useful stuff)
Post Reply