[info] Proteus - Waterproof, High-feature ECU!

[Abricos]

I have EGT ...
I use EGT ...

[Lambo97]

Interesting, Soon we will be able to run Pulsejet or Turbine with Rus EFI!

[JRD McLAREN]

Interesting, Soon we will be able to run Pulsejet or Turbine with Rus EFI!

Contact Colin Furze ...

[AndreyB]

Available at https://www.shop.rusefi.com/

No longer available on eBay

[puff]

wtf?? is there any rationale behind that decision by eBay?

[Simon@FutureProof]

Banning all "emissions defeat devices" basically.

Seems to be ebay.com only

[Abricos]

Banning all "emissions defeat devices" basically.

Seems to be ebay.com only

But VAG TDI ECU still for sale on ebay ...))))

[AndreyB]

Available for sale https://shop.rusefi.com/

[subzero]

can i use stm32f407zgt6 or i need stm32f429?

[AndreyB]

can i use stm32f407zgt6 or i need stm32f429?

no stm32f407zgt6

https://github.com/rusefi/rusefi/wiki/Chip-Shortage-Parts-Interchange says "256KB RAM required" which stm32f407zgt6 is not

[kneelo]

Finally installed my v0.3 in my latest track car (Holden VE commodore with the LEO Alloytec HFV6). Car starts and runs... yay!

There are a few errors on the online pinout diagram for the 23pin connector I found in the process of getting it working. The main one is that pin 14 is listed as a gnd but is actually one of the usb comms lines. I was losing Usb whenever this plug was connected until I checked the schematic.

There was a couple of other pins that were also wrong related to usb signals on this connector, I think maybe these were marked as the canbus lines on the pinout from memory. I assume there has been a hardware change at some point between versions.

Also is there a summary anywhere of the hardware mods required to get the knock sensing working? If chip availability wasnt an issue I would probably just go with a new board. As it is Im thinking I might try and kludge this board.

[AndreyB]

There are a few errors on the online pinout diagram for the 23pin connector I found in the process of getting it working. The main one is that pin 14 is listed as a gnd but is actually one of the usb comms lines. I was losing Usb whenever this plug was connected until I checked the schematic.

You would not believe it - https://github.com/mck1117/proteus/blob/master/changelog.md was created about a week ago

I've just mentioned USB removal on the changelog.

[subzero]

Just a question bought for my w201 2.3 8v denso honda hall sensor that needs 12 volt and outpouts 12 volt square signal
Proteus can accept 12 volt digital input for rpm signal?

[AndreyB]

Yes digital inputs are 12v tolerant when official parts were soldered.

[tmbryhn]

Is the LPS22HHTR sensor compatible with Proteus firmware?
According to datasheet, it should have the exact same footprint and pinout as the current LPS25HB, and also the same pressure range.

LPS25HB: https://no.mouser.com/ProductDetail/511-LPS22HHTR
LPS22HHTR: https://no.mouser.com/ProductDetail/511-LPS22HHTR

If not compatible; would it be an option to tweak the firmware to allow for use of multiple alternatives during these times of supply chain issues?

[mck1117]

Yes, the firmware supports both

[AndreyB]

digikey just randomly had x86 of VNLD5090 in stock a week ago and those were in fact delivered today!

Mouser was promising VNLD5300 with 11/2022 delivery, three days after order it's 03/2023 delivery

[AndreyB]

The cap I have is CAP-WADMLPC2.

UB-20AFMM-LL7A01 is matching USB cable.

[AndreyB]

Note to self: serial still works

RX pin is green on my blue uart device but that's totally not standardized

image.png (200.7 KiB) Viewed 841 times