Hi there,
Is it much work to add 4 more Ignition outputs in the software? Instead of 8, I would like 12
And yes, Dual IGN/INJ Table would be nice too. Just add a Table Switch function
Regards from Norway!
Adding more ignition outputs to software.
- Snake____1
- Posts: 37
- Joined: Sun Sep 04, 2016 6:05 pm
- Location: Norway
Adding more ignition outputs to software.
(X) BMW E36 318i M50B50 Turbo (MegaSquirt (KdFI v1.3))
(X) BMW E36 325tds M70B50 (ViPEC V88)
(X) BMW E36 328i M52B28 Turbo (rusEFI PnP @me)
(✓) BMW E36 320i M70B50 (rusEFI project car)
(✓) BMW E46 325Xi M57D30 (daily)
(X) BMW E36 325tds M70B50 (ViPEC V88)
(X) BMW E36 328i M52B28 Turbo (rusEFI PnP @me)
(✓) BMW E36 320i M70B50 (rusEFI project car)
(✓) BMW E46 325Xi M57D30 (daily)
- AndreyB
- Site Admin
- Posts: 14331
- Joined: Wed Aug 28, 2013 1:28 am
- Location: Jersey City
- Github Username: rusefillc
- Slack: Andrey B
Re: Adding more ignition outputs to software.
Actually internally it was 12 forever, just added the remaining 4 into the tunerstudio tuning file - it takes about 30 minutes for the fresh bundle to be ready. So do you have plans for a 12 cylinder engine??? Please tell us more.
Norway is a beautiful country
Norway is a beautiful country
Very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
Always looking for C/C++/Java/PHP developers! Please help us see https://rusefi.com/s/howtocontribute
Always looking for C/C++/Java/PHP developers! Please help us see https://rusefi.com/s/howtocontribute
- Snake____1
- Posts: 37
- Joined: Sun Sep 04, 2016 6:05 pm
- Location: Norway
Re: Adding more ignition outputs to software.
Plans for the BMW M70B50 v12 engine, hopefully full sequential setup and turbos Going for the Toyota/Denso 90919-02230 Coils btw.
I saw the TunerStudio config file, should have looked before asking Sorry
Another thing. Is the "bits" hardcoded, or can i change the display name?
For example:
ignitionPins1 = bits, U32, 708, [0:6], "PA0",
to:
ignitionPins1 = bits, U32, 708, [0:6], "IGN1",
I saw the TunerStudio config file, should have looked before asking Sorry
Another thing. Is the "bits" hardcoded, or can i change the display name?
For example:
ignitionPins1 = bits, U32, 708, [0:6], "PA0",
to:
ignitionPins1 = bits, U32, 708, [0:6], "IGN1",
(X) BMW E36 318i M50B50 Turbo (MegaSquirt (KdFI v1.3))
(X) BMW E36 325tds M70B50 (ViPEC V88)
(X) BMW E36 328i M52B28 Turbo (rusEFI PnP @me)
(✓) BMW E36 320i M70B50 (rusEFI project car)
(✓) BMW E46 325Xi M57D30 (daily)
(X) BMW E36 325tds M70B50 (ViPEC V88)
(X) BMW E36 328i M52B28 Turbo (rusEFI PnP @me)
(✓) BMW E36 320i M70B50 (rusEFI project car)
(✓) BMW E46 325Xi M57D30 (daily)
- AndreyB
- Site Admin
- Posts: 14331
- Joined: Wed Aug 28, 2013 1:28 am
- Location: Jersey City
- Github Username: rusefillc
- Slack: Andrey B
Re: Adding more ignition outputs to software.
The idea is for the project file to be universal and not depend on the board - remember we have two boards and some people are actually using their own boards. The default properties in the default firmware are already leaning towards the Frankenso board so I think we should be good as is.Snake____1 wrote:For example:
ignitionPins1 = bits, U32, 708, [0:6], "PA0",
to:
ignitionPins1 = bits, U32, 708, [0:6], "IGN1",
Very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
Always looking for C/C++/Java/PHP developers! Please help us see https://rusefi.com/s/howtocontribute
Always looking for C/C++/Java/PHP developers! Please help us see https://rusefi.com/s/howtocontribute