Page 1 of 1

Tunerstudio Refactoring

Posted: Sat Jul 06, 2019 11:27 am
by 960
I am working at a TS refactoring, and have a .ini file here if anyone will try it out.

It's far from finished, as some firmware additions/changes are required

Any feedback welcome.

1.07

[The extension ini has been deactivated and can no longer be displayed.]

[The extension ini has been deactivated and can no longer be displayed.]



All menus are cleaned up and grouped more rational


javaw_sgQoXMie6m.png
javaw_sgQoXMie6m.png (526.41 KiB) Viewed 14468 times
javaw_h5vudyOZEL.png
javaw_h5vudyOZEL.png (531.85 KiB) Viewed 14467 times

Re: Tunerstudio Refactoring

Posted: Sun Jul 07, 2019 9:59 pm
by AndreyB
My current focus is https://github.com/rusefi/rusefi/issues/866 which I believe would contribute towards end goal of user-friendly general purpose PID.

Re: Tunerstudio Refactoring

Posted: Mon Jul 08, 2019 5:17 am
by 960
Good!

Gp-pwm maps are among the most needed additions for this to be complete.

I have a new .ini file with more added and fully working.

Also waiting for TS to add the 1d array support to replace the curves.

[The extension ini has been deactivated and can no longer be displayed.]


Re: Tunerstudio Refactoring

Posted: Mon Jul 08, 2019 3:39 pm
by 960
I have also made some different dashboard layouts I will post here.

I am currently trying to add presets for all the most common sensors + injectors.


Here are a typical dash for tuning
Tuning.zip
(263.85 KiB) Downloaded 466 times
javaw_pcSR8mYyvI.png
javaw_pcSR8mYyvI.png (713.54 KiB) Viewed 14406 times
uO04MrwTqe.png
uO04MrwTqe.png (622.2 KiB) Viewed 14406 times

Re: Tunerstudio Refactoring

Posted: Tue Jul 09, 2019 12:05 am
by Abricos
and how to use it ???
need instruction how to used
where to add this file (rusefi_refactored.ini) ???
when to add this is a file ???

Re: Tunerstudio Refactoring

Posted: Tue Jul 09, 2019 3:06 am
by 960
Abricos wrote:
Tue Jul 09, 2019 12:05 am
and how to use it ???
need instruction how to used
where to add this file (rusefi_refactored.ini) ???
when to add this is a file ???
Just go to File, Vehicle Projects, Project properties and select the .ini file.

Or you can create new project, and load this ini instead of the .ini you normally use.

For the dashboard, just right click mouse button and select load dashboard at top of the menu.

Re: Tunerstudio Refactoring

Posted: Tue Jul 09, 2019 11:55 pm
by 960
A new .ini with a little more fixes and more added.
(Accel Enrichments + Spark Edge)

EDIT: I have been uploading the file with Pin-mapping.
This would be the right ones:

[The extension ini has been deactivated and can no longer be displayed.]

[The extension ini has been deactivated and can no longer be displayed.]

Can someone change the ignition pin mode to Falling and Rising in firmware?
(Instead of default, default inverted...)

Re: Tunerstudio Refactoring

Posted: Wed Jul 10, 2019 6:58 pm
by 960
Today we also got support for 1d arrays in TS.

This is very useful when tuning cold start, and work with several arrays at the same time.
8PTmFUZsAk.png
8PTmFUZsAk.png (376.45 KiB) Viewed 14331 times

Re: Tunerstudio Refactoring

Posted: Fri Jul 19, 2019 4:02 pm
by 960
A little more cleanup and changes.

Scaled the factoring to be % for corrections. (% Of normal fueling)

When connecting to board with this .ini, choose "use controller settings".

(Actually % of cranking base fuel pulse width for some of them, dont know how to change)

Started some rearranging/grouping in full pinout.


V 1.07

[The extension ini has been deactivated and can no longer be displayed.]

[The extension ini has been deactivated and can no longer be displayed.]


(these gauges added by Matt are really helpful to tune the ETB BTW)

F9Csx5Z9mc.png
F9Csx5Z9mc.png (406.76 KiB) Viewed 14272 times
iTplXTGjAn.png
iTplXTGjAn.png (375.32 KiB) Viewed 14275 times

Re: Tunerstudio Refactoring

Posted: Fri Jul 19, 2019 5:09 pm
by Abricos
Yes it's really cool EBT calibration set up ...

Re: Tunerstudio Refactoring

Posted: Fri Jul 19, 2019 7:42 pm
by 960
Abricos wrote:
Fri Jul 19, 2019 5:09 pm
Yes it's really cool EBT calibration set up ...
Thanks!

Trying to simplify a little, it can be confusing :-)

Have you tried the .ini file?

Re: Tunerstudio Refactoring

Posted: Fri Jul 19, 2019 7:50 pm
by 960
I would also like to add presets for ETB's, so the part-numbers/type can be in a drop down.

If someone could make a initial preset would be great. (I dont know how)

I would also like to add presets for injectors and sensors, as I have pages of values for anything possible.

If someone could show me, I can do the job.

I dont suppose this layout will be used, but I am sure some parts could be useful.

Re: Tunerstudio Refactoring

Posted: Fri Jul 19, 2019 9:31 pm
by 960
And I made it for the sensors :-)

[The extension ini has been deactivated and can no longer be displayed.]

[The extension ini has been deactivated and can no longer be displayed.]

EKWwx5IrWH.png
EKWwx5IrWH.png (304.7 KiB) Viewed 14262 times

Re: Tunerstudio Refactoring

Posted: Tue Aug 27, 2019 8:42 pm
by 960
Now with different dashes as pages :-)
javaw_uJYPfb0tl0.png
javaw_uJYPfb0tl0.png (448.61 KiB) Viewed 14055 times
javaw_lKhjo33wjT.png
javaw_lKhjo33wjT.png (342.85 KiB) Viewed 14055 times
javaw_jWx1y3hjca.png
javaw_jWx1y3hjca.png (335.08 KiB) Viewed 14055 times

Re: Tunerstudio Refactoring

Posted: Wed Aug 28, 2019 3:12 am
by Abricos
Only pic ??
How to used ?

Re: Tunerstudio Refactoring

Posted: Wed Aug 28, 2019 2:09 pm
by 960
Abricos wrote:
Wed Aug 28, 2019 3:12 am
Only pic ??
How to used ?
Extract this and put in your Tunerstudioprojects folder.

Let me know if/how it works.
1.07_By_960.zip
(2.81 MiB) Downloaded 466 times

Re: Tunerstudio Refactoring

Posted: Wed Aug 28, 2019 2:49 pm
by 960
If TS performs too slow, just right-click some of the dashes at the bottom and remove them.

You can also remove some gauges at some pages to make it improve.

If there are any bugs, or you want any changes/additions to menus, let me know.

You have to use TS Beta for this to work as it should.