[README] End users, PLEASE subscribe to this topic - MAJOR firmware announcements

It's all about the code!
Post Reply
User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

This thread is used to announce MAJOR firmware changes which could affect all users. Please subscribe if you use rusEfi.

A typical example of an announcement would be incompatible configuration change - in such cases you one cannot simply flash latest firmware but some kind of special considerations would be needed.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

Just made an incompatible configuration change - please load&save&migrate your settings via TS while updating to latest version. This was about https://github.com/rusefi/rusefi/issues/688
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

trigger input code could be FUBAR at the moment, will update this post once https://github.com/rusefi/rusefi/issues/767 is fixed
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

https://github.com/rusefi/rusefi/issues/776 is hopefully an improvement which makes I and D term scale of all PID settings to use the right time scale, so all I and D pid settings would need to be adjusted accordingly.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

We have changed the way some corrections are treated under https://github.com/rusefi/rusefi/issues/773 - so while migrating to latest the scale of configuration has changed.

Bumping configuration version to 1.06 to highlight the fact of incompatible change.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

https://github.com/rusefi/rusefi/issues/805 "calibrate TPS" feature is now (hopefully) working again with Tuner Studio. Please use latest project .ini file.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

Incompatible configuration change - https://github.com/rusefi/rusefi/commit ... 39f5af4b1a

You would need to migrate configuration prior to 20190712 version migration: save settings in TunerStudio project & update mainController.ini file.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

Idle air valve PID now has iTermMin/iTermMax settings, if you migrate to latest firmware you might need to manually set this value. min=-200 max=200 is a good starting point to have same behavior as previously. See https://github.com/rusefi/rusefi/issues/913
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

FSIO https://github.com/rusefi/rusefi/issues/922 incompatible change:

fan_on_setting is now cfg_fanOnTemperature
fan_off_setting is now cfg_fanOffTemperature

Please adjust your FSIO settings if you use these variables!
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

https://github.com/rusefi/rusefi/issues/796 is now fixed. This interesting defect mostly affects users with few tooth trigger wheels like Miata and similar Mitsubishi, mostly low RPM like cranking is affected - sometimes spark would not happen altogether. That's an important one unless you have a 36/1 or 60/2 trigger!
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

With https://github.com/rusefi/rusefi/pull/1029 stepper pin modes are now used - so if you had non-default mode configured behavior would now change!
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

We've made incompatible changes to TS gauges - data logging speed could go up with smaller data packet, but you would need to create new project if you update to latest firmware.

Configuration part of the project was not changed, only the gauges.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

https://github.com/rusefi/rusefi/pull/1112 changes the way we handle TPS calibration, please re-calibrate your TPS.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

User avatar
AndreyB
Site Admin
Posts: 10036
Joined: Wed Aug 28, 2013 1:28 am
Location: Jersey City
Soldering skill: yes
Coding skill?: yes
Contact:

Re: End users, PLEASE subscribe to this topic - MAJOR firmware announcements

Post by AndreyB »

We had a major defect since November 2019 - trigger sensors processing was inverted. This is now fixed https://github.com/rusefi/rusefi/issues/1176 - please update to latest firmware and maybe you would have to un-invert your settings.

That's a good point for a new release - https://github.com/rusefi/rusefi/releases

Going forward we should have a release every couple of months, with 6+ bundles attached to it.
https://rusefi.com/s/howtocontribute
very limited telepathic abilities - please post logs & tunes where appropriate - http://rusefi.com/s/questions
my skype is arro239

Post Reply